HLG-240-36C - LED Controller Mean Well - Free user manual and instructions
Find the device manual for free HLG-240-36C Mean Well in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Controller / Driver |
| Brand | Mean Well |
| Model | HLG-240-36C |
| Output Voltage | 36V DC |
| Output Power | 240W |
| Input Voltage | 90-305V AC |
| Input Frequency | 47-63Hz |
| Efficiency | Up to 94% |
| Dimming Function | 3-in-1 dimming (0-10V, PWM, resistance) |
| Protection | Short circuit, over voltage, over temperature, overload |
| IP Rating | IP65 |
| Cooling | Convection cooling |
| Mounting | Wall mounting |
| Dimensions (L x W x H) | 215mm x 113.3mm x 38.8mm |
| Weight | 1.44 kg |
| Operating Temperature | -40°C to +70°C |
| Certifications | UL, CUL, TUV, CE |
| Warranty | 5 years |
Frequently Asked Questions - HLG-240-36C Mean Well
How do I connect the input wires?
Connect the AC input wires to the terminals marked L (line), N (neutral), and PE (ground). Ensure the power is off before wiring. Use a screwdriver to secure the wires and check the polarity carefully.
Can I use it outdoors?
Yes, this device is rated IP65, making it dust-tight and protected against water jets. It can be used outdoors, but the AC connector should be properly sealed to maintain the rating.
What does the dimming function do?
The 3-in-1 dimming function allows you to control the output current by 0-10V DC signal, PWM signal, or a resistor. This enables smooth dimming of connected LED lighting.
How to adjust the output voltage or current?
Use the built-in potentiometer (labeled V/I ADJ) on the device to fine-tune the output voltage or current within the specified range. Turn it clockwise to increase, counterclockwise to decrease.
What happens if I overload it?
The device has built-in overload protection. If the connected load exceeds the rated power, the output will shut down to protect the driver. The LED will restart once the overload condition is removed.
How to clean and maintain the device?
Disconnect the power before cleaning. Wipe the exterior with a soft dry cloth. Avoid using water or solvents. Periodically check for dust accumulation on the case and heat sink to ensure proper cooling.
Is it compatible with LED strips?
Yes, as long as the LED strip's voltage requirement is 36V DC and the total power does not exceed 240W. Verify the strip's current draw to avoid overloading the driver.
How to troubleshoot if the LED doesn't light?
Check the input power and wiring connections first. Then verify the output voltage with a multimeter. If no output, test the dimming wires (if used) or the overload condition. Replace the device if it still fails.
Can I use it as a general 36V power supply?
It is primarily designed for LED lighting, but it can be used as a standard 36V DC power supply for devices within its power and voltage range, as long as the load is constant voltage compatible.
What is the recommended wiring gauge?
For input, use AWG 14-16 wires. For output, use AWG 18-20 wires depending on the current. Always follow local electrical codes and ensure connections are tight.
User questions about HLG-240-36C Mean Well
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your LED Controller in PDF format for free! Find your manual HLG-240-36C - Mean Well and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HLG-240-36C by Mean Well.
USER MANUAL HLG-240-36C Mean Well
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Mean Well
Model : HLG-240-36C
Category : LED Controller