CP-X2514WNEF - Projector HITACHI - Free user manual and instructions
Find the device manual for free CP-X2514WNEF HITACHI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LCD Projector |
| Brand | Hitachi |
| Model | CP-X2514WNEF |
| Display Technology | 3LCD (Polysilicon TFT Active Matrix) |
| Native Resolution | XGA (1024 x 768) |
| Brightness | 2500 ANSI Lumens |
| Contrast Ratio | 500:1 |
| Lamp Type | 210W UHP |
| Lamp Life | Up to 3000 Hours (Eco Mode) |
| Projection Size | 30 to 300 Inches |
| Keystone Correction | Vertical ±30 Degrees |
| Input Interfaces | 2x VGA (RGB), 1x S-Video, 1x Composite Video, 1x Audio In |
| Output Interfaces | 1x VGA (RGB), 1x Audio Out, 1x RS-232C Control |
| Noise Level | 32 dB (Eco Mode) |
| Built-in Speaker | 1 x 1 Watt |
| Dimensions (W x D x H) | 306 x 249 x 86 mm |
| Weight | 2.9 kg |
| Power Consumption | 280W Typical / 3W Standby |
| Power Supply | AC 100-240V, 50/60Hz |
| Safety Features | Auto Power Off, Key Lock, Password Security |
| Cleaning and Maintenance | Clean Air Filter Monthly; Replace Lamp as Needed |
| Spare Parts and Repairability | Lamp Module, Remote Control, Air Filter Available |
Frequently Asked Questions - CP-X2514WNEF HITACHI
How do I turn on the projector?
Press the POWER button on the projector or the remote control. The power indicator will light up and the lamp will start. Wait a few seconds for the image to appear.
How do I connect my laptop?
Use a VGA cable to connect the laptop's monitor port to the COMPUTER IN port on the projector. Then select the correct input source by pressing SOURCE on the remote.
How do I adjust the picture sharpness?
Use the FOCUS ring on the lens to sharpen the image, and the ZOOM ring to fit the screen size. Turn the rings until the image is clear and properly sized.
How do I replace the lamp?
Switch off the projector and unplug it. Wait for the lamp to cool. Open the lamp cover on the top or rear, loosen the lamp module screws, and pull out the old lamp. Insert the new lamp module (Hitachi DT01131 or compatible) and tighten the screws. Reset the lamp timer from the menu.
Why is my image trapezoid?
If the projector is not perpendicular to the screen, use KEYSTONE correction. Press the KEYSTONE button and adjust the vertical keystone using the arrow keys until the image is rectangular.
How do I clean the air filter?
Turn off the projector and unplug it. Locate the air filter on the side. Gently remove the filter and vacuum or wash it with mild soap and water. Let it dry completely before reinstalling. Clean every 100 hours of use.
Can I connect a speaker system?
Yes, use an audio cable from the projector's AUDIO OUT jack to your amplifier or powered speakers. The built-in speaker is only 1W.
What is the best projection distance for a 100-inch screen?
For a 100-inch diagonal screen, the projector should be placed approximately 3.0 meters away, depending on zoom. Adjust within the zoom range to fine-tune.
How do I change the projection mode for ceiling mount?
In the menu, go to SETUP, select PROJECTOR POSITION, and choose one of the options: Desktop Front, Desktop Rear, Ceiling Front, or Ceiling Rear.
What does the status light mean?
The power light flashes green when warming up. A steady green means on. If the lamp light flashes red, the lamp needs replacement. If the temp light flashes red, the projector may be overheating causing it to shut down.
User questions about CP-X2514WNEF HITACHI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Projector in PDF format for free! Find your manual CP-X2514WNEF - HITACHI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CP-X2514WNEF by HITACHI.