CDC-TI (V1.0A) - Motherboard ECS - Free user manual and instructions
Find the device manual for free CDC-TI (V1.0A) ECS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Motherboard |
| Brand | ECS (Elitegroup) |
| Model | CDC-TI (V1.0A) |
| Chipset | Intel 845GV / ICH4 |
| CPU Socket | Socket 478 |
| Supported Processors | Intel Pentium 4 / Celeron |
| Front Side Bus | 533 / 400 MHz |
| Memory Type | DDR SDRAM |
| Memory Slots | 2 x 184-pin DIMM |
| Maximum Memory | 2 GB |
| Expansion Slots | 1 x AGP 4X, 3 x PCI |
| Storage Interfaces | 2 x ATA-100, 1 x FDD |
| USB Ports | 4 x USB 2.0 |
| Onboard Graphics | Intel Extreme Graphics |
| Audio | Realtek ALC655 6-channel |
| LAN | 10/100 Mbps Ethernet |
| Form Factor | ATX |
| Dimensions | 305 x 244 mm |
| Weight | 1.2 kg |
| Power Requirements | ATX power supply |
| Operating Temperature | 0°C to 45°C |
| BIOS | Award BIOS, 4 Mb Flash |
| Included Accessories | I/O shield, IDE cable, SATA cable, manual |
| Warranty | 1-year limited warranty |
Frequently Asked Questions - CDC-TI (V1.0A) ECS
How do I install the CPU on the ECS CDC-TI motherboard?
Locate the Socket 478 on the motherboard. Lift the lever, align the notch on the CPU with the socket, gently place it in, and close the lever. Ensure the CPU is seated properly before applying thermal paste and attaching the cooler.
What is the maximum memory supported and what type?
The motherboard supports up to 2 GB of DDR SDRAM using two 184-pin DIMM slots. It is recommended to use matched pairs for dual-channel operation.
How can I reset the BIOS password?
Power off the system, unplug the power cord, and move the CMOS jumper (CLR_CMOS) to clear position for a few seconds. Alternatively, remove the onboard battery for 10 minutes. Then restore settings.
Does this motherboard support SATA drives?
No, the CDC-TI is an older model with only IDE (ATA-100) connectors. To use SATA drives, you would need an add-on controller card.
How do I enable the onboard graphics?
The motherboard includes integrated Intel Extreme Graphics. Connect your monitor to the VGA port on the rear I/O panel. If you have a discrete AGP card installed, the onboard graphics may be automatically disabled.
What is the maximum CPU speed supported?
The board supports Intel Pentium 4 processors up to 3.06 GHz with a 533 MHz front side bus, and Celeron processors up to 2.80 GHz.
How can I update the BIOS?
Download the latest BIOS from the ECS website, create a bootable USB or floppy, and run the flashing utility (e.g., AWDFLASH). Ensure stable power during the process.
Why does my system not power on?
Check the ATX power supply connections, the front panel switch wiring, and the power supply itself. Also verify that the CPU and memory are properly installed.
Can I use DDR2 memory?
No, the motherboard only supports DDR (original) memory. DDR2 is physically different and not electrically compatible.
Is there onboard LAN?
Yes, the board includes a 10/100 Mbps Ethernet controller (Realtek or similar) with an RJ45 port on the rear panel.
User questions about CDC-TI (V1.0A) ECS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motherboard in PDF format for free! Find your manual CDC-TI (V1.0A) - ECS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CDC-TI (V1.0A) by ECS.
USER MANUAL CDC-TI (V1.0A) ECS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ECS
Model : CDC-TI (V1.0A)
Category : Motherboard