ONU-10XG-1004-10G - Network Equipment AIRLIVE - Free user manual and instructions
Find the device manual for free ONU-10XG-1004-10G AIRLIVE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Optical Network Unit (ONU) for XGS-PON |
| Brand | AirLive |
| Model | ONU-10XG-1004-10G |
| Category | Network Equipment |
| Dimensions | Approximately 160 x 110 x 30 mm |
| Weight | Approximately 300 g |
| Power Supply | 12V DC, 1A external adapter |
| Power Consumption | Up to 12W |
| WAN Interface | 1 x 10G XGS-PON port (SC/APC) |
| LAN Interfaces | 4 x 10/100/1000 Mbps Gigabit Ethernet ports |
| Ethernet Cabling | CAT5e or higher recommended |
| Management | Web-based interface, TR-069 remote management |
| LED Indicators | PON, LOS, Power, LAN status LEDs |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Operating Humidity | 10% to 90% non-condensing |
| Security | Supports AES-128 encryption for XGS-PON |
| Installation | Wall-mountable with screws (included) |
| Maintenance | Clean externally with a soft dry cloth; do not use liquids |
| Safety | Keep away from water and heat; ensure proper ventilation |
| Repairability | No user-serviceable parts; contact your service provider for repair |
| Package Contents | ONU, power adapter, Ethernet cable, quick start guide |
Frequently Asked Questions - ONU-10XG-1004-10G AIRLIVE
How do I connect my ONU-10XG-1004-10G to the internet?
Connect the fiber to the PON port, then a Gigabit Ethernet cable from a LAN port to your computer or router. Plug in the power adapter and wait for the PON LED to become solid.
The LOS LED is blinking or red. What does that mean?
LOS indicates loss of signal. Check the fiber cable and ensure it's firmly connected to the PON port. If the issue persists, contact your internet service provider.
Can I use my own WiFi router with this ONU?
Yes, connect your WiFi router to any LAN port, set it to gateway mode, and configure your Internet settings (e.g., PPPoE or Dynamic IP) as provided by your ISP.
How do I reset the ONU to factory defaults?
Press and hold the reset button with a paperclip for about 10 seconds until the power LED blinks. The device will reboot with factory settings.
What are the default login credentials for the web interface?
The default IP is typically 192.168.1.1 with username/password admin/admin. Check the quick start guide as they may vary by ISP.
How many LAN ports does the ONU have and what speed?
It has four Gigabit Ethernet LAN ports, each supporting up to 10/100/1000 Mbps.
Does the ONU support wireless or WiFi?
No, this model is a wired ONU. You need a separate WiFi router or access point for wireless connectivity.
Where should I place the ONU for best performance?
Place it in a well-ventilated area, away from direct sunlight, heat, and moisture. Avoid sharp bends in the fiber and Ethernet cables.
How do I clean the ONU?
Use a soft, dry cloth to wipe the exterior. Do not use liquids or chemical cleaners, especially on the fiber connector.
What should I do if the device becomes very hot?
Ensure at least 10 cm clearance on all sides for ventilation. If it still overheats, contact your service provider as the device may be faulty.
User questions about ONU-10XG-1004-10G AIRLIVE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Network Equipment in PDF format for free! Find your manual ONU-10XG-1004-10G - AIRLIVE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ONU-10XG-1004-10G by AIRLIVE.
USER MANUAL ONU-10XG-1004-10G AIRLIVE
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : AIRLIVE
Model : ONU-10XG-1004-10G
Category : Network Equipment