AWH6204 - Water heater PHILIPS - Free user manual and instructions
Find the device manual for free AWH6204 PHILIPS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Water Heater |
| Brand | Philips |
| Model | AWH6204 |
| Mounting Type | Wall-mounted |
| Capacity | 6 liters |
| Power Consumption | 2000 W |
| Voltage | 220-240 V |
| Frequency | 50/60 Hz |
| Temperature Range | 30-75°C |
| Control Type | Mechanical thermostat |
| Safety Features | Overheat protection, pressure relief valve |
| Heating Element | Stainless steel |
| Tank Material | Enamel-coated steel |
| Insulation | High-density polyurethane foam |
| Installation Orientation | Vertical |
| Water Connection | 1/2 inch BSP |
| Net Weight | 5.5 kg |
| Dimensions (W x H x D) | 300 x 400 x 300 mm |
| Energy Efficiency Class | Class B |
| Maintenance | Annual descaling recommended |
Frequently Asked Questions - AWH6204 PHILIPS
How do I install the Philips AWH6204 water heater?
Installation must be done by a qualified technician. Mount the unit on a solid wall, connect the water inlet and outlet using 1/2 inch fittings, and ensure the pressure relief valve is accessible. Fill the tank before switching on the power.
Why is my water heater not producing hot water?
Check if the power supply is turned on and the thermostat is set correctly. If the thermal cutoff has tripped, press the reset button located near the thermostat. If the issue persists, the heating element may be defective.
How can I adjust the temperature on the AWH6204?
Use the thermostat dial on the front of the unit. Turn it clockwise for higher temperature or counterclockwise for lower. The recommended setting for energy savings is around 55-60°C.
How do I descale the water heater?
Turn off the power and water supply, drain the tank, then fill it with a descaling solution like citric acid. Let it sit for 30 minutes, then rinse thoroughly. Repeat annually for optimal efficiency.
What is the capacity of the AWH6204?
The AWH6204 has a 6-liter storage tank, ideal for a single sink or small handwash station. It provides hot water for short tasks, not for full showers.
Is it safe to use the water heater in a bathroom?
Yes, the unit is designed with IPX4 splash-proof protection. Ensure it is installed in a zone that complies with local electrical regulations, and always use a residual current device (RCD).
How can I reduce electricity consumption?
Set the thermostat to 55°C instead of maximum, insulate the hot water pipes, and limit the frequency of usage. Also, turn off the heater when not needed for extended periods.
What is the purpose of the pressure relief valve?
The valve releases excess pressure from the tank to prevent overpressure damage. It is a crucial safety component and should never be blocked or removed. Test it periodically by lifting the lever to ensure it operates freely.
Can the AWH6204 be used with solar water heating?
It can be connected to a solar pre-heating system as a backup. The cold water inlet can accept pre-heated water, but the maximum inlet temperature should not exceed 65°C to avoid damaging the thermostat.
How do I reset the safety cut-off?
Locate the reset button (usually near the thermostat) on the side of the unit. Press it firmly until it clicks. If the heater trips again immediately, call a service technician.
User questions about AWH6204 PHILIPS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual AWH6204 - PHILIPS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AWH6204 by PHILIPS.
USER MANUAL AWH6204 PHILIPS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : PHILIPS
Model : AWH6204
Category : Water heater