DADG-AK-G8-10-100 - Uncategorized Festo - Free user manual and instructions
Find the device manual for free DADG-AK-G8-10-100 Festo in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Pneumatic Cylinder (Linear Actuator) |
| Manufacturer | Festo |
| Model | DADG-AK-G8-10-100 |
| Bore Diameter | 10 mm |
| Stroke Length | 100 mm |
| Operating Pressure | 2 to 8 bar |
| Operating Temperature | -10°C to +60°C |
| Medium | Compressed air, filtered and lubricated |
| Piston Rod Diameter | 4 mm |
| Weight | Approximately 0.15 kg |
| Body Material | Anodized aluminum |
| Seal Material | Polyurethane or NBR |
| Mounting Type | Via accessories (foot, flange, trunnion) |
| Operation Mode | Double-acting |
| Cushioning | Elastic cushioning at end positions |
| Maintenance | Periodic check of air quality and seals |
| Cleaning | Wipe with a damp cloth; avoid solvents |
| Safety Features | Operate within rated pressure; avoid exceeding limits |
| Spare Parts | Seal kits available |
| Country of Origin | Germany |
Frequently Asked Questions - DADG-AK-G8-10-100 Festo
What is the operating pressure for the Festo DADG-AK-G8-10-100?
The recommended operating pressure for this pneumatic cylinder is between 2 and 8 bar. Always ensure the supply pressure is within this range to avoid damage or unreliable operation.
How do I connect the pneumatic cylinder?
Connect the cylinder to a pneumatic circuit using appropriate tubing and fittings. The cylinder has two ports; for double-acting operation, connect one port to the advance supply and the other to the retract supply, typically via a 5/2-way solenoid valve.
What type of air preparation is required?
Use filtered, regulated, and lubricated compressed air to ensure optimal performance and longevity. A typical FRL (filter-regulator-lubricator) unit is recommended, especially for high-cycle applications.
How can I adjust the speed of the cylinder?
Speed adjustment is achieved by installing flow control valves (also called speed controllers) at the cylinder ports. These allow you to regulate the exhaust air flow, thereby controlling the extension and retraction speed.
What does the model number DADG-AK-G8-10-100 mean?
The model code breaks down as follows: DADG is the series designator, AK indicates a variant (likely with rod thread or specific configuration), G8 is a basic code, 10 is the bore diameter in mm, and 100 is the stroke length in mm.
How do I mount the cylinder?
The cylinder can be mounted using accessory brackets such as foot mounts, flange mounts, or trunnion mounts. Ensure the mounting surface is aligned with the cylinder axis to avoid side loads that could cause premature wear.
What should I do if the cylinder does not move?
Check the air supply pressure first. Verify that the valve is operating and providing air to the correct port. Also inspect for blocked tubes, faulty seals, or a stuck piston. If the problem persists, disassemble and inspect the internal components.
What is the maximum allowed temperature for this cylinder?
The operating temperature range is -10°C to +60°C. Exceeding this range can degrade seals and reduce performance. For applications outside this range, contact Festo for suitable alternatives.
How do I replace seals on the DADG-AK-G8-10-100?
Seal replacement requires disassembling the cylinder. Use a seal kit from Festo. Carefully remove the old seals, clean the grooves, and install the new seals with proper lubrication. Reassemble following the manual, taking care not to damage the seals during installation.
Can I use this cylinder for vertical applications?
Yes, but ensure the cylinder has sufficient force to overcome the load and friction. For vertical lifting, consider using a valve with locking function or an integral brake to prevent unexpected motion in case of pressure loss. Counterbalance forces should be calculated carefully.
User questions about DADG-AK-G8-10-100 Festo
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual DADG-AK-G8-10-100 - Festo and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DADG-AK-G8-10-100 by Festo.
USER MANUAL DADG-AK-G8-10-100 Festo
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Festo
Model : DADG-AK-G8-10-100
Category : Uncategorized