SD-6276-SS1Q - Uncategorized Seco-Larm - Free user manual and instructions
Find the device manual for free SD-6276-SS1Q Seco-Larm in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of product | Electronic Door Access Control |
| Brand | Seco-Larm |
| Model | SD-6276-SS1Q |
| Dimensions | 165 x 114 x 50 mm (6.5 x 4.5 x 2 in) |
| Weight | 680 g (1.5 lbs) |
| Material | Stainless steel |
| Power supply | 12V DC (500mA adaptor required) |
| Standby current | 30 mA |
| Operating current | 150 mA |
| Relay output | 1 Form C (NO/NC) rated 2A @ 30V DC |
| User capacity | 100 user codes |
| Keypad | 12-key metal, backlit |
| Weatherproof rating | IP65 |
| Operating temperature | -20°C to +60°C |
| Operating modes | Toggle, Timed, Momentary |
| Programming | Via rear keypad or remote master code |
| Tamper switch | Yes, built-in |
| Mounting | Surface mount on standard 1-gang junction box |
| Maintenance | Clean with a soft dry cloth |
| Safety | Overcurrent protection and tamper alarm |
| Spare parts | Available from Seco-Larm (contact support) |
| Compliance | CE, FCC |
Frequently Asked Questions - SD-6276-SS1Q Seco-Larm
How do I install the Seco-Larm SD-6276-SS1Q?
Installation requires mounting the unit on a door frame near a standard junction box. Connect the power supply (12V DC) and the door strike or maglock to the relay contacts. Use the provided template for drilling holes. Tighten all screws securely.
How do I set the master code?
Enter the default master code (usually 1234) on the keypad, then press the * key to enter programming mode. Follow the instructions to change the master code. Choose a 4-8 digit code and confirm.
How can I reset the device to factory settings?
Disconnect power for 30 seconds, then reconnect. Press the reset button inside the housing for 5 seconds. The device will restore default codes and settings.
How do I add or delete user codes?
In programming mode, select "Add User" and enter the user number (01-100) followed by the new user code. To delete, select "Delete User" and enter the user number. Confirm with the # key.
What is the maximum distance for connecting the door strike?
The relay output can handle up to 2 Amps, so the distance depends on the wire gauge. For 22 AWG wires, a 50-foot (15-meter) run is typical. Use larger gauge for longer lengths.
Is the keypad weatherproof?
Yes, the SD-6276-SS1Q has an IP65-rated weatherproof keypad, suitable for outdoor use. Ensure the rubber gasket is properly seated during installation.
How do I clean and maintain the device?
Use a soft, slightly damp cloth to wipe the keypad and housing. Do not use solvents or abrasive cleaners. Inspect wiring connections periodically and tighten if necessary.
What should I do if the keypad is not responding?
Check the power supply voltage and connections. Ensure the unit is properly grounded. If the issue persists, perform a factory reset. If still not working, contact Seco-Larm technical support.
Can I connect a remote release button to the SD-6276-SS1Q?
Yes, the device supports an external request-to-exit (REX) input. Connect the button to the REX terminals (normally open). Pressing the button will release the door without entering a code.
How do I set the relay time for automatic relocking?
In programming mode, select "Relay Time" and choose a duration from 1 to 99 seconds. The default is 5 seconds. Enter the desired time and press # to save.
User questions about SD-6276-SS1Q Seco-Larm
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual SD-6276-SS1Q - Seco-Larm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SD-6276-SS1Q by Seco-Larm.
USER MANUAL SD-6276-SS1Q Seco-Larm
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Seco-Larm
Model : SD-6276-SS1Q
Category : Uncategorized