InvisiPac HM50 24Y114 - Uncategorized GRACO - Free user manual and instructions
Find the device manual for free InvisiPac HM50 24Y114 GRACO in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Hydraulic Pump for High-Viscosity Materials |
| Model Number | InvisiPac HM50 24Y114 |
| Brand | Graco |
| Dimensions (H x W x D) | 28 x 23 x 28 in (71 x 58 x 71 cm) |
| Weight | 45 lb (20.4 kg) |
| Power Source | Hydraulic Motor (Hydraulic fluid required) |
| Max Fluid Pressure | 3300 psi (22.8 MPa) |
| Max Flow Rate | 0.75 gpm (2.8 L/min) |
| Fluid Inlet Size | 1/2 in NPT(f) |
| Fluid Outlet Size | 1/4 in NPT(f) |
| Hose Connection | Swivel 3/8 in NPT(m) |
| Wetted Materials | Stainless steel, tungsten carbide, PTFE |
| Warranty | Graco Standard Warranty (refer to manual) |
| Recommended Fluid Viscosity | Up to 50,000 cps |
| Operating Temperature | 40–100 °F (4–38 °C) |
| Noise Level | Less than 85 dB(A) |
| Maintenance | Daily: drain water separator, check hydraulic oil; Weekly: clean intake filter; Monthly: check hoses |
| Safety Precautions | Wear safety glasses and gloves; depressurize before servicing; use only compatible fluids |
| Spare Parts | Repair kits (24Y114-REPAIR) include seals, valves, and pistons |
| Repairability | Modular design allows easy replacement of major components |
Frequently Asked Questions - InvisiPac HM50 24Y114 GRACO
What type of hydraulic fluid does the InvisiPac HM50 require?
Use a premium grade anti-wear hydraulic oil with viscosity ISO 46 or equivalent. Refer to the manual for specific recommendations.
How do I prime the pump before first use?
Ensure the fluid supply valve is open and the pressure relief valve is open. Run the hydraulic motor at low speed until fluid flows steadily from the outlet, then close the relief valve.
What is the maximum continuous operating pressure?
The InvisiPac HM50 is rated for a maximum continuous fluid pressure of 3300 psi (22.8 MPa). Do not exceed this pressure.
How often should I replace the seals?
Seal life depends on fluid type and usage. Inspect seals monthly for wear or leakage. Replace using the 24Y114-REPAIR kit as needed.
Can I use the pump for water-based paints?
The pump is designed for high-viscosity materials like adhesives and sealants. For water-based paints, consult Graco technical support to ensure compatibility with wetted parts.
What should I do if the pump loses prime?
Check that the inlet strainer is clean, the fluid supply is sufficient, and all valves are open. If necessary, manually fill the pump chamber with fluid through the outlet port.
How do I store the pump when not in use?
Flush the pump with a compatible solvent, drain all fluid, and store in a dry area. Apply a light coat of oil to exposed metal parts to prevent corrosion.
Where can I find the serial number?
The serial number is stamped on a metal plate attached to the pump frame, near the hydraulic motor. It is also printed on the original packaging.
What hydraulic flow rate is required?
The pump requires a hydraulic flow of 5–10 gpm (19–38 L/min) at a pressure of 1800–2000 psi. Refer to the specification sheet for exact requirements.
How do I troubleshoot erratic output?
Check for a clogged inlet line, worn piston seals, or air in the hydraulic system. Inspect the check valves for debris. If the problem persists, contact Graco service.
User questions about InvisiPac HM50 24Y114 GRACO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual InvisiPac HM50 24Y114 - GRACO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. InvisiPac HM50 24Y114 by GRACO.
USER MANUAL InvisiPac HM50 24Y114 GRACO
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : GRACO
Model : InvisiPac HM50 24Y114
Category : Uncategorized