RMX-70 - Receiver ROTEL - Free user manual and instructions
Find the device manual for free RMX-70 ROTEL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo FM/AM Receiver |
| Brand | Rotel |
| Model | RMX-70 |
| Power Output | 70W per channel into 8 ohms (20Hz-20kHz, both channels driven) |
| Total Harmonic Distortion | <0.03% |
| Frequency Response | 20Hz - 20kHz ±0.5dB |
| Input Sensitivity (Line) | 150mV |
| Signal-to-Noise Ratio | 100dB (line) |
| Dimensions (W x H x D) | 432mm x 100mm x 305mm |
| Weight | 9.5 kg |
| Power Consumption | 350W (max) |
| Inputs | Phono (MM), 4 Line (Tape, CD, Tuner, Aux), Tape Monitor |
| Outputs | Speaker A/B, Preamp Out, Rec Out, Headphone (6.3mm) |
| Tuner Bands | FM (87.5-108 MHz), AM (530-1710 kHz) |
| Remote Control | Included (infrared) |
| Special Features | Tone controls (bass, treble), Balance, Loudness, Subsonic filter |
| Maintenance | Clean with a soft dry cloth. Avoid harsh chemicals. |
| Safety Instructions | Operate in a well-ventilated area, avoid moisture, unplug during storms or when unused for long periods. |
| Spare Parts & Repairability | Contact Rotel authorized service centers for genuine parts. Designed for long-term serviceability. |
| General Information | Handcrafted in Japan/China. Refer to user manual for complete details. |
Frequently Asked Questions - RMX-70 ROTEL
How do I connect speakers to the Rotel RMX-70?
Use the Speaker A or Speaker B terminals on the back. Ensure the impedance is 8 ohms or higher. Connect positive to red and negative to black. Remove about 10mm of insulation and tighten the binding posts.
What is the maximum power output of the RMX-70?
The RMX-70 delivers 70 watts per channel into 8 ohms, 20Hz-20kHz, both channels driven. For 4 ohm speakers, power output is typically higher but check the manual for stability.
How do I set up the FM antenna?
Connect the supplied FM dipole antenna to the FM 75 ohm terminal. Stretch it out horizontally for best reception. For AM, use the loop antenna included, rotating it for minimal noise.
Why is there no sound from the speakers?
Check that the speaker selector (A or B) is engaged, volume is not at minimum, and the input source is selected. Ensure the mute function is off. Also verify speaker connections.
Can I use the RMX-70 with a TV?
Yes, connect the TV's audio output (RCA or headphone) to an available Line input (e.g., Aux). Select that input on the receiver. For best quality, use the TV's analog output.
How do I clean the RMX-70?
Use a soft dry cloth to wipe the chassis. For stubborn dirt, slightly dampen the cloth with water. Never use alcohol, ammonia, or abrasive cleaners. Avoid getting moisture inside.
What is the phono input for?
The Phono input is designed for turntables with a moving magnet (MM) cartridge. It includes a built-in phono preamp. Connect your turntable's RCA cables to this input and ground wire to the screw terminal.
How do I perform a factory reset?
There is no factory reset button. To reset tuner presets, press and hold the Memory button while powering on. For other settings, manually adjust each control to neutral positions.
What are the dimensions of the RMX-70?
The receiver measures 432mm wide, 100mm high, and 305mm deep. Weight is approximately 9.5 kg. Ensure adequate ventilation, leaving at least 10cm above.
Where can I find spare parts?
Contact an authorized Rotel service center for genuine parts. Visit Rotel's official website for a list of service locations. Do not attempt internal repairs yourself.
User questions about RMX-70 ROTEL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual RMX-70 - ROTEL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. RMX-70 by ROTEL.