InformaCast VIP-402A-IC - Loudspeaker Valcom - Free user manual and instructions
Find the device manual for free InformaCast VIP-402A-IC Valcom in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | IP Ceiling Loudspeaker |
| Brand | Valcom |
| Model | InformaCast VIP-402A-IC |
| Category | Loudspeaker |
| Dimensions (W x H x D) | 8.5 x 8.5 x 3.5 inches (216 x 216 x 89 mm) |
| Weight | 1.5 lbs (0.68 kg) |
| Power Supply | Power over Ethernet (PoE) IEEE 802.3af |
| Input Voltage | 48V DC (PoE) |
| Power Consumption | 12.95W (max) |
| Audio Output | 2W RMS |
| Frequency Response | 100 Hz - 15 kHz |
| Network Interface | 10/100 Mbps Ethernet |
| Supported Protocols | InformaCast, SIP, Multicast |
| Speaker Type | 8-ohm, 2-inch full-range driver |
| Mounting | Ceiling mount (flush or tile) |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Operating Humidity | 10% to 90% (non-condensing) |
| Material | Metal grille, plastic housing |
| Certifications | FCC Part 15, CE, RoHS |
| Maintenance | Wipe with dry cloth; avoid liquids |
| Spare Parts / Repairability | None user-serviceable; contact Valcom support |
| Included Items | Loudspeaker, mounting hardware, quick start guide |
| Warranty | 2 years limited |
Frequently Asked Questions - InformaCast VIP-402A-IC Valcom
How do I install the Valcom InformaCast VIP-402A-IC loudspeaker?
Mount the speaker in a ceiling tile using the included hardware. Connect an Ethernet cable with PoE from a switch. The speaker will obtain an IP address via DHCP. Refer to the InformaCast configuration guide for network setup.
What power source does the VIP-402A-IC require?
It uses Power over Ethernet (PoE) standard IEEE 802.3af. Ensure your network switch provides PoE or use a PoE injector.
Can I use this speaker without InformaCast?
Yes, the speaker supports SIP and multicast protocols. It can be used with any compatible IP paging system or PBX.
How do I adjust the volume?
Volume is configured via the InformaCast admin interface or through SIP commands. There is no physical volume knob.
What is the audio quality like?
The speaker delivers clear voice announcements with a frequency response of 100 Hz to 15 kHz and 2W RMS output.
Does this speaker support multiple zones?
Yes, when used with InformaCast, you can assign the speaker to specific zones for targeted paging.
How do I reset the speaker to factory defaults?
Press and hold the reset button (located on the back) for 10 seconds until the LED flashes. This will clear network settings and reboot.
Can I mount this speaker on a wall?
The design is optimized for ceiling mounting. Wall mounting may affect audio dispersion. Use an optional bracket if needed.
What should I do if the speaker does not power on?
Check the Ethernet cable connection and ensure the switch port provides PoE. Verify the LED indicates power. If not, try a different cable or port.
Where can I find the user manual?
The manual is available for free download at notice-facile.com in PDF format.
User questions about InformaCast VIP-402A-IC Valcom
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Loudspeaker in PDF format for free! Find your manual InformaCast VIP-402A-IC - Valcom and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. InformaCast VIP-402A-IC by Valcom.
USER MANUAL InformaCast VIP-402A-IC Valcom
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Valcom
Model : InformaCast VIP-402A-IC
Category : Loudspeaker