AP6310SN-GN - Access Point HUAWEI - Free user manual and instructions
Find the device manual for free AP6310SN-GN HUAWEI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Access Point |
| Brand | Huawei |
| Model | AP6310SN-GN |
| Dimensions (W x D x H) | 210 mm x 210 mm x 50 mm |
| Weight | 1.2 kg |
| Power Supply | PoE (802.3af) or DC 12V |
| Power Consumption | 12 W (typical) |
| Wireless Standards | IEEE 802.11b/g/n |
| Frequency Band | 2.4 GHz |
| Maximum Data Rate | 300 Mbps (2x2 MIMO) |
| Antenna Type | Internal dual-band antennas |
| Interfaces | 1 x 10/100/1000 Base-T (PoE in), 1 x RS232 console port |
| LED Indicators | Power, Ethernet, WLAN, Alarm |
| Operating Temperature | -10°C to 55°C |
| Security | WPA/WPA2-PSK, 802.1X, WEP |
| Mounting | Ceiling or wall mount (brackets included) |
| Certifications | CE, FCC, RoHS |
| Management | Web-based, CLI, SNMP |
| Operating Humidity | 5% to 95% (non-condensing) |
| Warranty | 1 year limited |
Frequently Asked Questions - AP6310SN-GN HUAWEI
How do I reset the AP6310SN-GN to factory defaults?
Press and hold the reset button on the device for at least 10 seconds using a paperclip. The device will reboot and restore factory settings.
What is the default IP address of the access point?
The default IP address is 192.168.0.1. Ensure your computer is on the same subnet to access the web interface.
How do I configure the access point for the first time?
Connect the AP to your network via PoE or DC power. Set your computer to a static IP in the 192.168.0.x range, then open a browser to 192.168.0.1. Log in with default credentials (admin/admin).
Can I mount the AP6310SN-GN outdoors?
The AP6310SN-GN is designed for indoor use only. For outdoor installation, use a weatherproof enclosure.
How do I update the firmware?
Download the latest firmware from the Huawei support site. Log into the web interface, go to System > Firmware Upgrade, select the file, and click Upgrade. Do not power off during the process.
What should I do if clients cannot connect to the Wi-Fi?
Check if the SSID is broadcasted, ensure clients are using the correct security key, and verify that the AP is connected to the network with a working Ethernet cable. Also confirm the AP is not overloaded.
Does the AP6310SN-GN support Power over Ethernet?
Yes, it supports 802.3af PoE. Use a PoE switch or injector to power the device via the Ethernet port.
How can I extend the Wi-Fi range using this access point?
You can use the AP as a wireless repeater if the firmware supports it, or connect multiple APs via Ethernet and configure them with the same SSID and security settings for seamless roaming.
What security protocols are supported?
The AP supports WPA/WPA2-PSK, WPA-Enterprise (802.1X), and legacy WEP. WPA2 is recommended for best security.
How do I access the CLI for advanced configuration?
Connect a console cable to the RS232 port on the AP. Use a terminal emulator (e.g., PuTTY) with settings: 9600 baud, 8 data bits, no parity, 1 stop bit. Default login credentials are admin/admin.
User questions about AP6310SN-GN HUAWEI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Point in PDF format for free! Find your manual AP6310SN-GN - HUAWEI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AP6310SN-GN by HUAWEI.
USER MANUAL AP6310SN-GN HUAWEI
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HUAWEI
Model : AP6310SN-GN
Category : Access Point