AXDCT-2 - Car radio AXESS - Free user manual and instructions
Find the device manual for free AXDCT-2 AXESS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Radio / Audio Receiver |
| Brand | AXESS |
| Model | AXDCT-2 |
| Dimensions (W x H x D) | 188 mm x 58 mm x 160 mm (Standard 1-DIN) |
| Weight | 0.6 kg |
| Power Supply | 12V DC (negative ground) |
| Maximum Power Output | 4 x 50 watts (peak) |
| Radio Bands | AM/FM |
| Playback Media | USB, AUX, SD card |
| Bluetooth | Yes, for hands-free calling and audio streaming |
| Display | LCD with white backlight |
| Audio Controls | Volume, Bass, Treble, Balance, Fader |
| Equalizer Presets | Rock, Pop, Classic, Flat, Jazz |
| Remote Control | Included (wired or wireless not specified) |
| Front Panel | Detachable for theft prevention |
| Power Output (RMS) | 4 x 20 watts (typical) |
| Frequency Range | FM: 87.5-108 MHz; AM: 530-1710 kHz |
| Operating Temperature | -20°C to 60°C |
| Maintenance | Clean with a soft, dry cloth. Avoid solvents. |
| Safety | Built-in fuse (10A) to protect against short circuits |
| Spare Parts & Repairability | Contact AXESS service center for replacement parts |
| Certifications | CE, RoHS compliant |
Frequently Asked Questions - AXDCT-2 AXESS
How do I install the AXESS AXDCT-2 car radio?
First, disconnect the vehicle's battery. Then, remove the existing radio, connect the wiring harness to your car's wiring (matching colors: yellow for constant power, red for ignition, black for ground, etc.), and slide the unit into the DIN slot. Secure with the mounting sleeve.
How do I pair my phone via Bluetooth?
Turn on the radio and enable Bluetooth on your phone. Search for devices and select 'AXDCT-2'. If prompted, enter PIN '0000' or '1234'. Once paired, you can stream music or make calls.
Why is there no sound from the speakers?
Check that the speakers are properly connected and the balance/fader settings are not set to one side. Also ensure the volume is turned up and the source is playing. Verify the radio fuse is intact.
Can I use the radio without a battery connection?
No, the radio requires a 12V DC power source. It will not operate solely on battery power. The yellow wire must be connected to a constant 12V supply to retain memory settings.
How do I reset the radio to factory settings?
Press the reset button (if available) using a pointed object, or disconnect the yellow and red power wires for a few minutes. Alternatively, access the system menu and select 'Factory Reset'.
What type of USB flash drive is supported?
The radio supports USB flash drives formatted in FAT32 with up to 32GB capacity. It can play MP3 and WMA audio files.
How do I set the clock?
Press the 'MODE' button until the clock appears. Then use the 'UP' or 'DOWN' buttons to adjust hours and minutes. Confirm by pressing 'MODE' again or waiting a few seconds.
Why does the radio turn off after a few minutes?
This may be due to the car's ignition switch cutting power when the engine is off. Ensure the red wire is connected to an accessory (ACC) power source. Some vehicles have a timer that shuts off accessories.
Can I connect an external amplifier?
Yes, the AXDCT-2 has RCA preamp outputs (front and rear) that allow connection to an external amplifier. Adjust the output level via the radio's audio settings.
How do I clean the front panel?
Gently remove the detachable faceplate. Wipe it with a soft, slightly damp cloth. Do not use abrasive cleaners or water directly on the unit. Ensure it is completely dry before reattaching.
User questions about AXDCT-2 AXESS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Car radio in PDF format for free! Find your manual AXDCT-2 - AXESS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AXDCT-2 by AXESS.