Duoblock PRO 350 G8 - Car alarm Positron - Free user manual and instructions
Find the device manual for free Duoblock PRO 350 G8 Positron in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Alarm System |
| Brand | Positron |
| Model | Duoblock PRO 350 G8 |
| Power Supply | 12V DC (vehicle battery) |
| Current Consumption | Standby: < 20 mA, Alarm: < 500 mA |
| Siren Output | 130 dB |
| Remote Control Frequency | 433.92 MHz |
| Remote Control Range | Up to 100 meters (line of sight) |
| Number of Remotes Included | 2 |
| Shock Sensor | Adjustable dual-zone shock sensor |
| Engine Immobilizer | Yes, via relay cut-off |
| Central Locking Interface | Compatible with most cars (negative/positive trigger) |
| Panic Mode | Yes, triggered from remote |
| Valet Mode | Yes, via override button |
| Maintenance | Check battery voltage periodically; clean sensor lens with dry cloth |
| Safety Features | Starter kill, anti-scan code, false alarm prevention |
| Spare Parts Available | Remote controls, siren, shock sensor, wiring harness |
| Repairability | Modular components; replace defective module |
| Dimensions (Control Unit) | 120 x 70 x 25 mm |
| Weight (Control Unit) | 150 g |
Frequently Asked Questions - Duoblock PRO 350 G8 Positron
How do I program the remote controls?
To program a remote, turn the ignition ON, press the valet button 3 times within 5 seconds, then press and hold the remote button until the siren chirps. Repeat for additional remotes. Refer to the manual for exact steps.
What does the shock sensor do?
The shock sensor detects impacts on the vehicle. It has two zones: a light impact triggers a warning chirp, while a heavy impact triggers the full alarm. Adjust sensitivity with a small screwdriver.
How to reset the alarm after a false trigger?
Disarm the system using the remote. If the remote does not work, turn the ignition ON and press the valet button to bypass the alarm. Check the battery in the remote if issues persist.
Can I use the alarm with a remote starter?
Yes, the Duoblock PRO 350 G8 has a remote start input. However, installation requires additional relays. Consult a professional installer.
How do I change the remote battery?
Remove the key ring, pry open the case with a small flathead screwdriver, and replace the CR2032 battery. Ensure correct polarity. Test the remote after reassembly.
What is the valet mode?
Valet mode disables the alarm while the vehicle is being serviced. To engage, turn the ignition ON and press the valet button for 2 seconds until the LED stays on. Repeat to exit.
How to wire the alarm to my car's central locking?
Identify your car's lock/unlock wires (negative or positive trigger). Connect the alarm's lock/unlock outputs accordingly. Use the wiring diagram included. Test with a multimeter before connecting.
Why does the alarm chirp randomly?
This could be due to a loose door trigger wire or a faulty shock sensor. Check all door switch connections and reduce shock sensor sensitivity. If chirping continues, disable the warning chirp in settings.
Can I install the alarm myself?
Basic installation is possible if you have experience with car electronics. However, improper wiring can damage the vehicle. Professional installation is recommended.
Where is the model number located?
The model number (Duoblock PRO 350 G8) is printed on the control unit label and on the packaging. Keep this number for support.
User questions about Duoblock PRO 350 G8 Positron
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Car alarm in PDF format for free! Find your manual Duoblock PRO 350 G8 - Positron and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Duoblock PRO 350 G8 by Positron.