Elevate BD3632IS - Distributeur automatique réfrigéré Structural Concepts - Free user manual and instructions
Find the device manual for free Elevate BD3632IS Structural Concepts in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Commercial Refrigerated Display Case |
| Model | Elevate BD3632IS |
| Brand | Structural Concepts |
| Width | 35.6 in (90.4 cm) |
| Depth | 32.1 in (81.5 cm) |
| Height | 78.0 in (198.1 cm) |
| Net Weight | 345 lb (156.5 kg) |
| Power Supply | 115 V, 60 Hz, 15 A |
| Refrigerant | R-290 (Propane) |
| Temperature Range | 33°F to 41°F (0.5°C to 5°C) |
| Number of Doors | 1 |
| Door Type | Sliding glass with heater |
| Interior Lighting | LED, automatic on/off with door |
| Shelves | 4 adjustable wire shelves |
| Thermostat | Digital, front-mounted |
| Defrost | Automatic, electric |
| Castors | 4 locking, heavy-duty |
| Certifications | NSF, cETLus, ENERGY STAR |
| Condenser | Rear-mounted, removable air filter |
| Cleanable Gaskets | Replaceable magnetic gaskets |
| Warranty | 3 years parts and labor |
Frequently Asked Questions - Elevate BD3632IS Structural Concepts
What is the recommended ambient temperature for the Elevate BD3632IS?
The unit operates best in ambient temperatures between 60°F and 80°F (15°C to 27°C). Placing it in direct sunlight or near heat sources can affect performance.
How do I clean the condenser coils?
Unplug the unit and remove the rear grille. Use a soft brush or vacuum with a crevice tool to gently clean the coils every 3 months to maintain efficiency.
Can I change the sliding door from left to right?
The sliding door is field-reversible. Instructions are in the manual: remove the top and bottom tracks, swap the door, and reinstall. Door panels are heavy; use two people.
What type of refrigerant does this model use?
The Elevate BD3632IS uses R-290 (propane), an environmentally friendly refrigerant. It is flammable; service must be performed by qualified technicians.
How do I adjust the temperature?
Press and hold the SET button on the digital controller for 3 seconds until the setpoint flashes. Use the up/down arrows to adjust between 33°F and 41°F, then press SET again.
The interior LED lights are not turning on. What should I check?
First, ensure the door switch is not obstructed. If lights still don't work, check the LED driver behind the top panel. A replacement driver kit is available from Structural Concepts.
Is this unit self-defrosting?
Yes, it has an automatic electric defrost cycle. The controller initiates defrost periodically; you may notice water dripping into the drain pan inside the unit.
Can I stack items on top of the display case?
No, the top surface is not designed to support weight. Avoid placing anything on top as it could damage the unit or create a safety hazard.
How do I replace the door gasket?
Peel off the old gasket from the door frame. Clean the groove with mild soap and water. Press the new gasket into place, starting at the top. Ensure a tight seal all around.
What should I do if the unit displays an error code?
Refer to the manual's error code table. Common codes: E1 (sensor failure), E2 (defrost thermistor failure). Try resetting by unplugging for 5 minutes, then plugging back in. If persistent, contact Structural Concepts support.
User questions about Elevate BD3632IS Structural Concepts
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Distributeur automatique réfrigéré in PDF format for free! Find your manual Elevate BD3632IS - Structural Concepts and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Elevate BD3632IS by Structural Concepts.