TC-NT2 - Network Cable Tester TRENDNET - Free user manual and instructions
Find the device manual for free TC-NT2 TRENDNET in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | IP Network Camera |
| Brand | TRENDnet |
| Model | TC-NT2 |
| Dimensions (H x W x D) | 4.8 x 2.4 x 2.4 inches (122 x 61 x 61 mm) |
| Weight | 0.5 lb (227 g) |
| Power Supply | 5V DC, 2A via AC adapter (included) |
| Image Sensor | 1/4-inch CMOS |
| Resolution | 640 x 480 (VGA) at up to 30 fps |
| Lens | Fixed, 4.0 mm, F2.0 |
| Night Vision | Up to 16 feet (5 m) with 8 IR LEDs |
| Connectivity | 10/100 Mbps Ethernet (RJ-45) |
| Wireless | Not applicable (wired only) |
| Supported Protocols | IPv4, HTTP, TCP/IP, UDP, SMTP, FTP, DHCP, NTP, DNS, DDNS, UPnP |
| Audio | Two-way audio (built-in microphone and speaker) |
| Storage | MicroSD slot (up to 32 GB) / Network storage (NAS) |
| Motion Detection | Yes, configurable zones and sensitivity |
| Management Software | TRENDnetView Pro, or web browser |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Mounting | Wall or ceiling mount bracket included |
| Maintenance | Clean lens with soft, dry cloth; keep vents clear |
| Safety Precautions | Use only provided power adapter; avoid exposure to rain |
| Included Accessories | Power adapter, Ethernet cable, mounting kit, user manual |
Frequently Asked Questions - TC-NT2 TRENDNET
How do I set up the TRENDnet TC-NT2 camera for the first time?
Connect the camera to your router using the provided Ethernet cable and power adapter. Install the TRENDnetView Pro software or use the camera's web interface (default IP: 192.168.10.100). Follow the setup wizard to configure network settings and password.
What is the default username and password for the TC-NT2?
The default username is admin and the password is admin. It is strongly recommended to change the password during initial setup for security.
Can I view the camera remotely from my smartphone?
Yes, you can use the TRENDnetView Pro app or access the camera via its web interface after configuring port forwarding on your router. Alternatively, use TRENDnet's DDNS service for easier remote access.
How do I enable night vision on the TC-NT2?
Night vision is automatically activated in low light conditions. The built-in IR LEDs illuminate the scene up to 16 feet. Ensure the camera's IR cut filter is set to 'Auto' in the settings menu.
What is the maximum resolution and frame rate?
The TC-NT2 captures video at a maximum resolution of 640 x 480 pixels (VGA) at up to 30 frames per second.
How can I reset the camera to factory defaults?
Press and hold the reset button on the camera's side for about 10 seconds using a paperclip. The camera will reboot with factory settings (IP: 192.168.10.100, admin/admin).
Does the camera support audio recording?
Yes, the TC-NT2 has a built-in microphone and speaker, supporting two-way audio. You can listen and speak through the camera using the software or app.
Can I connect the camera wirelessly?
No, the TC-NT2 is a wired-only model. It does not have built-in Wi-Fi. You must use an Ethernet cable to connect it to your network.
What type of storage is supported for recording?
The camera supports local storage via a MicroSD card (up to 32 GB) and network storage (NAS) using SMB/CIFS protocol. Recordings can be scheduled or triggered by motion.
Is the TC-NT2 weatherproof for outdoor use?
No, the TC-NT2 is designed for indoor use only. It is not weatherproof or rated for outdoor installation. For outdoor use, consider a weatherproof housing or an outdoor-rated model.
User questions about TC-NT2 TRENDNET
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Network Cable Tester in PDF format for free! Find your manual TC-NT2 - TRENDNET and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TC-NT2 by TRENDNET.