TS 1200X4 - Receiver Taramp’s - Free user manual and instructions
Find the device manual for free TS 1200X4 Taramp’s in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Audio Amplifier |
| Model | TS 1200X4 |
| Number of Channels | 4 |
| RMS Power (4 ohms) | 120W x 4 |
| RMS Power (2 ohms) | 200W x 4 |
| Bridged Power (4 ohms) | 400W x 2 |
| Frequency Response | 10Hz - 30kHz |
| Total Harmonic Distortion (THD) | <0.05% |
| Signal-to-Noise Ratio | >95dB |
| Input Sensitivity | 0.2V - 6V |
| Low-Pass Filter | 40Hz - 400Hz |
| High-Pass Filter | 40Hz - 400Hz |
| Bass Boost | 0-12dB at 45Hz |
| Dimensions (L x W x H) | 12.6 x 7.1 x 2.4 inches |
| Weight | 6.5 lbs |
| Power Supply Voltage | 10-16V DC |
| Protection Circuitry | Short circuit, thermal, overvoltage, undervoltage |
| Recommended Fuse | 40A x 2 |
| Mounting Type | Surface mount |
| Color | Heat sink silver / black chassis |
Frequently Asked Questions - TS 1200X4 Taramp’s
What is the recommended impedance for each channel?
Each channel is stable down to 2 ohms. For bridged operation, minimum impedance is 4 ohms.
How do I connect the amplifier to my car battery?
Use proper gauge power wire (4 AWG recommended) with a fuse close to the battery. Connect the remote wire to the head unit's remote output.
Can this amplifier be used for subwoofers?
Yes, you can bridge two channels to power a subwoofer, providing up to 400W RMS at 4 ohms.
What type of speaker wire should I use?
Use 12-16 AWG speaker wire for optimal performance. Ensure proper polarity.
Does the amplifier have a remote bass control?
No, the TS 1200X4 does not include a remote bass control. Bass boost is adjustable on the amplifier itself.
Why does my amplifier go into protect mode?
Common causes: short circuit in speaker wires, overheated (check ventilation), voltage too low or too high, or impedance below minimum. Check connections and cooling.
What is the maximum power output?
Maximum power is typically peak power, but the amplifier is rated for 1200W peak (400W x 4 at 2 ohms or bridged). RMS is the continuous rating.
Can I use this amplifier with a factory head unit?
Yes, but you may need a line output converter (LOC) if the factory head unit lacks RCA pre-outs.
How do I adjust the gain properly?
Set the head unit volume to 75% of max. Turn the gain knob counterclockwise (minimum). Play a test tone and increase gain until distortion is heard, then back off slightly.
Is the amplifier bridgeable?
Yes, channels 1-2 and 3-4 can be bridged. Connect the positive wire to the positive of one channel and the negative to the negative of the paired channel. Minimum bridged load is 4 ohms.
User questions about TS 1200X4 Taramp’s
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual TS 1200X4 - Taramp’s and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TS 1200X4 by Taramp’s.
USER MANUAL TS 1200X4 Taramp’s
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Taramp’s
Model : TS 1200X4
Category : Receiver