HTA-25B - Uncategorized Taga Harmony - Free user manual and instructions
Find the device manual for free HTA-25B Taga Harmony in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Integrated Amplifier |
| Power Output | 2 x 25W (8 ohms) |
| Frequency Response | 20 Hz - 20 kHz ±0.5 dB |
| Total Harmonic Distortion | < 0.05% |
| Input Sensitivity | 200 mV (line), 2.5 mV (phono) |
| Signal-to-Noise Ratio | > 90 dB (line), > 70 dB (phono) |
| Inputs | 4x RCA (line), 1x RCA (phono MM) |
| Outputs | Speaker A/B, Pre-out, Headphone (6.3mm) |
| Remote Control | Included (infrared) |
| Dimensions (W x H x D) | 430 x 100 x 300 mm |
| Weight | 8 kg |
| Power Supply | AC 110-240V, 50/60 Hz |
| Power Consumption | 200 W (max), <0.5 W standby |
| Speaker Impedance | 4 - 16 ohms |
| Tone Controls | Bass, Treble, Balance |
| Additional Features | Direct mode, Mute, Input selector |
| Cleaning | Wipe with dry, soft cloth; avoid solvents |
| Safety | Do not expose to moisture; disconnect when not in use |
| Spare Parts / Repairability | Contact Taga Harmony service center for genuine parts |
Frequently Asked Questions - HTA-25B Taga Harmony
How do I connect my turntable to the HTA-25B?
Connect your turntable to the Phono input. Ensure your turntable has a moving magnet (MM) cartridge and ground wire is connected to the ground terminal.
Can I use 4-ohm speakers with this amplifier?
Yes, the HTA-25B supports speaker impedance from 4 to 16 ohms. For 4-ohm speakers, avoid driving both channels at full volume to prevent overheating.
How do I switch between speakers A and B?
Use the Speaker A/B buttons on the front panel. You can select A, B, or both simultaneously. Note that using both sets may reduce power handling.
The amplifier does not power on. What should I check?
First, check the power cord and mains plug. Ensure the standby/on button is pressed. If still off, check the fuse on the rear panel and replace if blown.
How do I use the remote control?
Point the remote at the IR sensor on the front panel. Replace the batteries (2x AAA) if unresponsive. The remote controls volume, input selection, mute, and standby.
There is a humming noise from the speakers. What causes this?
Humming is often due to a ground loop. Ensure all components share the same power strip. For turntable use, check the ground wire connection.
Can I connect a subwoofer to this amplifier?
Yes, use the Pre-out output on the rear panel to connect an active subwoofer. The subwoofer will receive the full-range signal pre-amplification.
How do I clean the amplifier?
Unplug the unit. Use a soft, dry cloth to wipe the exterior. Do not use any solvents or abrasive cleaners. Avoid getting moisture into vents.
What is the recommended warm-up time?
For optimal sound quality, allow the amplifier to warm up for 15-20 minutes at low volume before critical listening.
Where can I find replacement parts like remote or knobs?
Contact Taga Harmony customer support or an authorized service center. Provide your model and serial number for accurate part ordering.
User questions about HTA-25B Taga Harmony
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual HTA-25B - Taga Harmony and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HTA-25B by Taga Harmony.
USER MANUAL HTA-25B Taga Harmony
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Taga Harmony
Model : HTA-25B
Category : Uncategorized