EKI-8510G-2FI - Switch Advantech - Free user manual and instructions
Find the device manual for free EKI-8510G-2FI Advantech in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed Industrial Ethernet Switch |
| Number of Ports | 8 x Gigabit RJ45 + 2 x Gigabit SFP |
| Dimensions (W x H x D) | 60 x 135 x 105 mm |
| Weight | 0.6 kg |
| Power Input | 12 ~ 48 VDC |
| Power Consumption | 10 W (max) |
| Operating Temperature | -40°C ~ 75°C |
| Mounting | DIN-rail or Panel |
| Switching Capacity | 20 Gbps |
| MAC Table Size | 8K |
| Management Features | Web, CLI, SNMP v1/v2c/v3, RMON |
| Redundancy Protocol | X-Ring, RSTP, MSTP |
| VLAN Support | 802.1Q VLAN, up to 256 groups |
| QoS | 8 priority queues, 802.1p, DSCP |
| Security | 802.1X, ACL, Port Security |
| Regulatory Certifications | CE, FCC |
| Protection Class | IP30 |
| Spare Parts | Power supply, SFP modules, DIN-rail kit |
| Maintenance | Clean with dry cloth; avoid liquids |
| Safety Precautions | Use only approved power source; disconnect before cleaning |
Frequently Asked Questions - EKI-8510G-2FI Advantech
What is the default IP address of the EKI-8510G-2FI?
The default IP address is 192.168.0.100 with subnet mask 255.255.255.0.
How do I reset the switch to factory defaults?
Press and hold the Reset button for 5 seconds while power is on. The device will reboot with factory settings.
How to configure VLANs on this switch?
Access the web interface, go to VLAN Configuration, create VLAN groups and assign ports. Use 802.1Q tagging for trunk ports.
How to update firmware?
Download the firmware from Advantech support. In web GUI, go to Maintenance > Firmware Upgrade, upload file and reboot.
How to connect via console cable?
Use an RS-232 cable with settings: 115200 baud, 8 data bits, no parity, 1 stop bit. Connect to the console port.
How to enable X-Ring redundancy?
In web GUI, navigate to Redundancy > X-Ring, designate two ports as ring ports and enable the ring.
How to set up SNMP for monitoring?
Go to SNMP Configuration, set community strings (e.g., public for read-only), and enable traps if needed.
What to do if a port shows no link?
Check cable connections, verify device power, test with known working cable, and ensure port is not disabled via software or port security.
How to mount the switch on a DIN rail?
Attach the DIN-rail bracket to the back of the switch, snap onto the rail until it locks. Use a screwdriver to release the latch for removal.
What power supply is recommended?
Use a 12~48 VDC power supply with sufficient current (minimum 1A). Advantech recommends certified industrial power supplies.
User questions about EKI-8510G-2FI Advantech
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Switch in PDF format for free! Find your manual EKI-8510G-2FI - Advantech and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EKI-8510G-2FI by Advantech.
USER MANUAL EKI-8510G-2FI Advantech
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Advantech
Model : EKI-8510G-2FI
Category : Switch