RA-301 - Uncategorized Posiflex - Free user manual and instructions
Find the device manual for free RA-301 Posiflex in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Thermal Receipt Printer |
| Brand | Posiflex |
| Model | RA-301 |
| Print Technology | Direct Thermal |
| Paper Width | 80 mm (3.15 inches) |
| Print Speed | Up to 250 mm/s |
| Resolution | 203 dpi |
| Interface | USB, RS-232 Serial, Ethernet (optional) |
| Barcode Support | 1D and 2D barcodes |
| Cutting Mechanism | Automatic cutter (partial/full cut) |
| Dimensions (W x D x H) | 180 x 215 x 150 mm |
| Weight | 2.5 kg |
| Power Supply | 24V DC, 2.5A |
| Power Consumption | Printing: 50W, Standby: 5W |
| Operating Temperature | 0°C to 45°C |
| Humidity | 10% to 90% non-condensing |
| MTBF | 1,500,000 lines |
| MCBF | 60,000,000 lines |
| Warranty | 1 year limited |
Frequently Asked Questions - RA-301 Posiflex
How do I load paper into the Posiflex RA-301?
Open the paper cover, insert the paper roll with the thermal side facing up, and pull out a small length. Close the cover until it clicks. The printer will automatically feed the paper.
What type of paper does the RA-301 use?
It uses 80 mm wide thermal paper rolls. Standard roll diameter is up to 80 mm (3.15 inches). Ensure the paper is compatible with thermal printers.
How do I connect the printer to my computer?
Connect the printer via USB or RS-232 serial cable. Install the appropriate drivers from the Posiflex website or the included CD. The printer will appear as a standard printer device.
Why is the printer not printing?
Check the paper roll is installed correctly and the cover is closed. Ensure the power LED is on. Verify the USB or serial cable is securely connected. Try a different cable or port. If using serial, check baud rate settings (default 9600 bps).
How do I clean the print head?
Turn off the printer and open the cover. Use a cleaning pen or a cotton swab with isopropyl alcohol to gently wipe the print head. Allow it to dry completely before closing and using the printer. Avoid touching the print head with fingers.
What does the error LED indicate?
A solid red error LED usually indicates a paper jam or out-of-paper condition. A flashing LED may indicate a cover open error. Check the paper path and cover. If persistent, contact support.
Can I print graphics and logos?
Yes, the RA-301 supports bitmap graphics and logos. You can download them using the Posiflex utility or send commands (e.g., ESC/POS) to download and print logos.
How do I set the printer to cut automatically?
The printer supports automatic cutting by command. In your software, enable the cut command (e.g., ESC 'm' or GS V). You can also set partial cut mode (leaving a small bridge) to prevent paper from falling.
What are the default DIP switch settings?
Default settings are typically: DIP switch 1 (parity) OFF, 2 (baud rate) OFF for 9600 bps, 3 (handshake) OFF for XON/XOFF, 4 (protocol) OFF for standard. Refer to the manual for exact configuration.
Where can I find drivers and manuals?
Drivers, manuals, and utilities are available on the Posiflex official website under the support section. Alternatively, the product page on notice-facile.com provides a direct download link.
User questions about RA-301 Posiflex
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual RA-301 - Posiflex and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. RA-301 by Posiflex.
USER MANUAL RA-301 Posiflex
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Posiflex
Model : RA-301
Category : Uncategorized