RS300-E8-RS4 - Server ASUS - Free user manual and instructions
Find the device manual for free RS300-E8-RS4 ASUS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 1U Rackmount Server |
| Brand | ASUS |
| Model | RS300-E8-RS4 |
| Processor Support | Intel Xeon E3-1200 v3 series (LGA1150) |
| Chipset | Intel C224 |
| Memory | 4 x DIMM slots, DDR3 ECC, up to 32GB |
| Storage | 4 x 3.5" hot-swap SATA/SAS drive bays |
| RAID Support | Software RAID 0/1/10 (Intel RSTe) |
| Network | 2 x Intel I210AT Gigabit Ethernet |
| Management | ASUS ASMB8-iKVM (IPMI 2.0) |
| Expansion Slots | 1 x PCIe 3.0 x16 (low profile), 1 x PCIe 3.0 x8 |
| Power Supply | 300W single (80+ Gold optional) |
| Dimensions (W x D x H) | 444 x 497 x 43 mm (17.5 x 19.6 x 1.7 in) |
| Weight | Approximately 10 kg (22 lbs) |
| Cooling | 3 x 40mm system fans |
| Front I/O | 2 x USB 2.0, 1 x VGA |
| Rear I/O | 2 x USB 3.0, 1 x VGA, 2 x GbE, 1 x Serial |
| Operating Temperature | 10°C - 35°C (50°F - 95°F) |
| Certifications | CE, FCC, UL |
| Maintenance | Clean with dry compressed air; avoid liquid cleaners |
| Safety | Use anti-static wrist strap; disconnect power before servicing |
| Spare Parts | Available through ASUS authorized distributors |
| Reparability | Hot-swap drives, modular PSU, replaceable fans |
Frequently Asked Questions - RS300-E8-RS4 ASUS
How do I power on the ASUS RS300-E8-RS4 server?
Press the power button on the front panel once. Ensure the power supply is connected and the PSU switch is on.
What does the blinking LED on the front panel indicate?
A blinking power LED typically indicates a system standby or sleep state. A blinking HDD LED indicates drive activity.
How do I install a hard drive?
Locate the hot-swap drive tray, press the latch, pull the tray out. Install the 3.5-inch drive into the tray, secure with screws, then slide back into the bay until it locks.
How do I access the BIOS setup?
During boot, press Delete or F2 repeatedly until the BIOS setup screen appears.
What memory type does the server support?
The ASUS RS300-E8-RS4 supports DDR3 ECC memory modules at 1333/1600 MHz, up to 32 GB total (4 x 8 GB).
How do I reset the BMC (IPMI) settings?
You can reset the BMC via the BIOS by selecting Advanced > IPMI Configuration > Reset to Default, or use the physical jumper on the motherboard (see manual for location).
Can I use SAS drives in this server?
Yes, the server supports both SATA and SAS drives via the backplane, but a dedicated SAS controller may be required.
How do I configure RAID?
Enter the BIOS, go to Advanced > Intel RSTe (or use an add-on RAID controller) to create RAID 0, 1, or 10 arrays.
What is the default IPMI IP address?
The default IPMI IP is 192.168.1.1 with username admin and password admin (change immediately for security).
How do I update the firmware?
Download the latest firmware from the ASUS support website, then use the BMC web interface (under Maintenance > Firmware Update) or bootable DOS tools.
User questions about RS300-E8-RS4 ASUS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual RS300-E8-RS4 - ASUS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. RS300-E8-RS4 by ASUS.
USER MANUAL RS300-E8-RS4 ASUS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ASUS
Model : RS300-E8-RS4
Category : Server