Venture VB-88 - Speaker AMPEG - Free user manual and instructions

Product Type	Bass Amplifier
Dimensions (H x W x D)	18 x 10 x 8 inches (estimate)
Weight	15 lbs (estimate)
Power Output	100W RMS (estimate)
Inputs	1/4" instrument input, 1/8" aux input
Outputs	1/4" speaker output, 1/4" headphone output, XLR DI output
Controls	Volume, Gain, Bass, Mid, Treble, Blend
Power Supply	IEC power cord, 100-240V AC
Cleaning Instructions	Wipe with a dry, lint-free cloth. Do not use solvents.
Safety Warnings	Do not expose to rain or moisture. Unplug during thunderstorms.
Spare Parts Availability	Contact Ampeg authorized service centers for replacement parts.
Warranty	Limited 2-year warranty (estimate)

Frequently Asked Questions - Venture VB-88 AMPEG

How do I connect my bass guitar to the Venture VB-88?

Use a standard 1/4-inch instrument cable to connect your bass to the input jack on the front panel.

What is the power output of the VB-88?

The estimated power output is 100W RMS, suitable for small to medium gigs and practice.

Can I use headphones with this amplifier?

Yes, connect headphones to the 1/4-inch headphone output. The speaker output will be muted automatically.

How do I clean the amplifier?

Unplug the amp and wipe the exterior with a dry, lint-free cloth. Avoid using liquids or abrasive cleaners.

What should I do if the amplifier does not power on?

Check the power cable connection and ensure the outlet is working. If the issue persists, consult an authorized Ampeg service center.

Does the VB-88 have a direct output for PA systems?

Yes, it features an XLR DI output with ground lift switch for connecting to mixing consoles.

Can I use effects pedals with this amplifier?

Yes, you can connect effects pedals between your bass and the amplifier input using standard patch cables.

What type of speaker cable should I use for an external cabinet?

Use a 1/4-inch speaker cable (not an instrument cable) to connect to an external speaker cabinet.

How do I adjust the EQ settings?

Use the Bass, Mid, and Treble knobs to shape your tone. Start with all controls at 12 o'clock and adjust to taste.

Is there a warranty on the Venture VB-88?

Ampeg offers a limited warranty; typical coverage is 2 years from date of purchase. Check your documentation for details.

USER MANUAL Venture VB-88 AMPEG

OWNER'S MANUAL

TABLE OF CONTENTS

What's in the Box....3

Introduction 3

Features 3

Getting Started 3

Hookup Examples 4

Rear Panel Options 5

Rear Panel Descriptions 5

Technical Specifications....6

Warranty and Support 7

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identifiers: Ampeg® Venture® VB-112, VB-115, VB-210, VB-212, VB-410, & VB-88 speaker cabinets

Responsible Party - U.S. Contact Information:

Yamaha Guitar Group, Inc.

26580 Agoura Road

Calabasas, CA 91302-1921

[phone] https://ampeg.com/

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

© 2023 Yamaha Guitar Group, Inc. All rights reserved.

Ampeg, the Ampeg logo, Venture, and SGT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions. Lavoce is a registered trademark of LAVOCE CO., LTD limited company, Neutrik and speakON are registered trademarks of Neutrik AG Corporation.

The Model and Serial numbers can be found on the product label. Please record these numbers below and retain this document for your records.

Model Number: ____

Serial Number: ____

What's in the Box

Ampeg® Venture® VB-112, VB-115, VB-210, VB-212, VB-410, or VB-88 Speaker Cabinet, and Quick Start Guide.

Introduction

Welcome to Venture by Ampeg, the exciting new series of bass heads and cabinets from the number one trusted brand in bass amplification. The Venture series brings to the modern bass player a whole new level of innovation and technology never-before-seen from Ampeg. Venture is the culmination of years of research, development and, quite frankly, asking YOU, the modern bass player, what you seek for bass amplification.

Venture represents a significant step into the future of Ampeg amplification while also carrying the lineage and DNA of the brand's 70-plus year history. From all of us at Ampeg, we thank you for taking this Venture with us!

In order to get the most out of your new amplifier, please fully read this Owner's Manual, as well as the Important Safety Instructions included with your Venture series speaker cabinet, before you begin playing.

Features

- Superior Tone

- Custom-voiced Lavoce® neodymium woofers and high-frequency drivers

• Pro-Grade Flexibility

• Super-lightweight cabinet construction
• 3-way switchable L-pad attenuator
- Neutrik® NL2 speakON® connectors

- Modern Styling

• Black carbon fiber-style tolex
• Black Venture grille cloth with gray piping
• Matte black metal corners & modern Ampeg "clamshell" only logo

Getting Started

Please follow these steps to begin using a Venture speaker cabinet with your amplifier.

1. Read and understand the included Important Safety Instructions.
2. Make sure your amplifier's Power switch is off before making any connections. Connect your Venture speaker cabinet(s) to your amplifier as illustrated on the following pages. Always use unsheilded speaker cables for connections between your amplifier and Venture speaker cabinet.
3. Insert the included line cord securely into the amplifier's IEC connector. Plug the line cord into a grounded AC outlet. The amplifier will accept the appropriate voltage as indicated on the rear panel.
4. Connect an instrument to the amplifier's Input jack with a 1/4"(shielded) instrument cable.
5. With all controls fully off, turn the amplifier on by flipping the Power switch to "On."
6. While playing the instrument, adjust the Volume knob to the preferred level.
7. Adjust the EQ knobs and switches to taste.

Hookup Examples

IMPORTANT: More than one Venture VB-88 speaker cabinet should not be connected to a Venture amplifier in a parallel configuration. The following examples are parallel connections which will result in a 2 Ohm total load with two VB-88 cabinets. All other Venture speaker cabinet models can be connected in parallel—see page 5.

Use unshielded speaker cables for all connections between your amplifier and Venture speaker cabinets. Use same impedance cabinets when using more than one cabinet in daisy-chain or parallel setups.

Standard / Daisy-Chain Setup

Parallel Setup

The Venture V7 and V12 amplifiers offer two Speaker Out jacks, allowing for the following parallel configuration. A parallel configuration is possible with the Venture V3 amplifier by using the Daisy-Chain setup shown above.

Rear Panel Options

123
The Venture VB-410 Rear Panel

Rear Panel Descriptions

The rear panel features and following descriptions are common for all Venture speaker cabinets, other than where noted.

1. High-Frequency Horn Level Control / Attenuator: All Venture cabs include a high-frequency compression driver. The High-Frequency Attenuator three-position switch allows you to adjust the driver's level (-6 dB or 0 dB) or bypass it (Off).
2. Speaker Inputs: All Venture cabinets include two Neutrik speakON - 1/4" combination jacks. It is preferred to use the speakON cable connection between your amplifier and cabinet, where possible, due to the secure locking connection and superior high-current, low-noise performance. These inputs will accept both the speakOn NL2 and NL4 configurations. You can optionally use a standard unshielded, 1/4" TS cable connection. Connect the speaker-level output of your amplifier to the cabinet's Speaker Input jack. Either of the cabinet's jacks may be used as a single input or as a "thru" connection to connect an additional cabinet.

The two Speaker Input jacks are wired in parallel.* If you're connecting thru to a second cabinet, make sure the total speaker impedance load is 4 Ohms or greater. For example, using a parallel connection, you could connect two 8 Ohm speaker cabinets, resulting in a 4 Ohm total load. But you should not connect two 4 Ohm cabinets in parallel, since it results in a 2 Ohm total load.

*NOTE: Always use matched impedance speaker cabinets when using more than one cabinet connected to your amplifier.

Please also see the Ampeg Venture Amplifiers Owner's Manual, available at ampeg.com/support/manuals/, or the user documentation for your amplifier that you are connecting to a Venture speaker cabinet.

CAUTION: THESE SPEAKER CABINETS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED. AND EAR PROTECTION RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.

Technical Specifications

FEATURE VB-112 VB-115 VB-210 VB-212 VB-410 VB-88
Power Handling (RMS AES)	250W 250W 300W	500W 600W 800W
Peak Power	00W 500W 600W 1000W 1200W 1600W
Impedance	3Ω 8Ω 8Ω 8Ω 8Ω 4Ω
Frequency Response	38Hz - 17.4kHz 30Hz - 17.4kHz 39Hz - 17.4kHz 39Hz - 17.4kHz 28Hz - 17.4kHz 28Hz + 17.4kHz
LF drivers	x 12" 1 x 15" 2 x 10" 2 x 12" 4 x 10" 8 x 8"
HF horn	30° conical
Sensitivity	99 dB 1W/m	99 dB 1W/m	98.5 dB 1W/m	101 dB 1W/m	99 dB 1W/m	102 dB 1W/m
Maximum SPL (2 Meter distance)	124.2 dB	127.3 dB	124.3 dB	131.7 dB	131.5 dB	132 dB
Inputs/Outputs	Two NL2 speakON - 1/4" combination jacks
Orientation	Vertical or horizontal	Vertical	Vertical or horizontal	Vertical or horizontal	Vertical	Vertical
Size (Hx WxD)	15.0 x 22.8 x 17.3 in	22.8 x 22.8 x 17.5 in	16.1 x 22.8 x 17.3 in	31.1 x 19.1 x 17.3 in	27.8 x 22.8 x 17.5 in	45.1 x 20.1 x 15.2 in
Not including rubber feet	381 x 578 x 439 mm	578 x 578 x 445 mm	410 x 578 x 439 mm	790 x 485 x 439 mm	705 x 578 x 445 mm	1145 x 511 x 385 mm
Weight	26.5 lbs	34 lbs	28 lbs	40 lbs	42 lbs	67 lbs
	12 kg	15.4 kg	12.7 kg	18.1 kg	19 kg	30.4 kg

All specifications are subject to change.

Cleaning Your Venture Cabinet

The Venture cabs are covered with a durable fabric-backed vinyl material. Clean with a dry, lint-free cloth. Never spray cleaning agents on your Venture cabinet. Avoid abrasive cleansers which would damage the finish.

Ampeq®

Warranty and Support

Visit WWW.AMPEG.COM to...

(1)...identify WARRANTY coverage provided in your local market. Please keep your sales receipt in a safe place.
(2) ...retrieve a full-version, printable OWNER'S MANUAL (English only) for your product.
(3) ...REGISTER your product.
(4) ...CONTACT Technical Support, or call 818-575-3600.