DAV-6410 - Anemometer DAVIS - Free user manual and instructions
Find the device manual for free DAV-6410 DAVIS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Anemometer |
| Brand | Davis Instruments |
| Model | DAV-6410 |
| Measurement Range | 0 to 322 km/h (0 to 200 mph) |
| Accuracy | ±1 km/h or ±0.5 m/s (whichever is greater) |
| Resolution | 0.1 km/h |
| Starting Threshold | 1.0 m/s (2.2 mph) |
| Output Signal | Contact closure (pulse) or wireless (optional transmitter) |
| Dimensions | Height: 32 cm (12.6 in), Arm length: 21 cm (8.3 in) |
| Weight | 340 g (12 oz) |
| Materials | UV-resistant plastic cups, stainless steel shaft |
| Power Source | Passive (no power needed for pulse output); optional wireless transmitter uses solar cell with battery backup |
| Mounting | Mast mount with U-bolt (fits 1-1.25 in / 25-32 mm mast) |
| Cable Length | 12 m (40 ft) with RJ11 connector |
| Operating Temperature | -40°C to +65°C (-40°F to +149°F) |
| Environmental Rating | Weatherproof (IPX4 equivalent) |
| Compatibility | Davis Vantage Pro2, Vue, Console, and Envoy systems |
| Certifications | CE, FCC |
| Maintenance | Annual cleaning and bearing lubrication |
| Warranty | 2 years |
Frequently Asked Questions - DAV-6410 DAVIS
How do I install the DAV-6410 anemometer on a mast?
Secure the anemometer to a mast using the provided U-bolt. Ensure the mast diameter is between 1 and 1.25 inches (25-32 mm). Mount at least 2 meters above any obstructions for accurate readings.
What is the maximum cable length for the DAV-6410?
The standard cable is 12 meters (40 ft). For longer runs, use a shielded extension cable; total length should not exceed 100 meters to avoid signal loss.
Can the DAV-6410 be used with a Davis Vantage Pro2 console?
Yes, the DAV-6410 is fully compatible with Davis Vantage Pro2, Vue, and Envoy consoles. It connects via the RJ11 sensor port.
How do I calibrate the anemometer?
The DAV-6410 is factory calibrated. No user calibration is needed. If readings seem off, check for debris or bearing wear. Cleaning may restore accuracy.
What maintenance is required for the DAV-6410?
Clean the cups and shaft annually with a soft cloth. Lubricate the bearings with light machine oil (e.g., 3-in-1 oil) every two years or if spinning becomes rough.
Why does my anemometer stop spinning in light wind?
The starting threshold is 1.0 m/s (2.2 mph). Below this, the cups may not rotate. If it remains stuck in wind above 1 m/s, check for debris or bearing stiffness.
What is the expected lifespan of the DAV-6410?
With proper maintenance, the anemometer can last 5-10 years. UV exposure may cause plastic cups to become brittle; replace if cracked.
Can I use the DAV-6410 with a wireless transmitter?
Yes, an optional Davis Anemometer Transmitter Kit (part #6332) converts the wired signal to wireless for use with wireless consoles.
How do I test if the anemometer is working?
Connect the anemometer to a compatible console. Spin the cups manually; the console should display a non-zero wind speed. If no reading, check cable connections.
What should I do if the anemometer readings are erratic?
Inspect for loose connections, damaged cable, or bent cups. Clean the bearing and ensure the shaft is free of rust. If problems persist, contact Davis support.
User questions about DAV-6410 DAVIS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Anemometer in PDF format for free! Find your manual DAV-6410 - DAVIS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DAV-6410 by DAVIS.
USER MANUAL DAV-6410 DAVIS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : DAVIS
Model : DAV-6410
Category : Anemometer