DS-3E1518P-SI - Switch Hikvision - Free user manual and instructions
Find the device manual for free DS-3E1518P-SI Hikvision in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | PoE Managed Switch |
| Model | DS-3E1518P-SI |
| Ports | 16 x Gigabit PoE+ (10/100/1000) + 2 x Gigabit SFP |
| PoE Budget | 250 W |
| PoE Standard | IEEE 802.3af/at |
| Switching Capacity | 36 Gbps |
| Dimensions (W x D x H) | 440 x 210 x 44 mm (1U rack mount) |
| Weight | 3.5 kg |
| Power Supply | 100-240 V AC, 50-60 Hz, internal |
| Power Consumption | ≤ 300 W (including PoE) |
| Management | Web GUI, CLI, SNMP v1/v2c/v3, RMON |
| VLAN Support | 802.1Q VLAN, up to 256 VLANs |
| QoS | 8 queues, port-based, 802.1p, DSCP |
| Security | 802.1X, ACL, port security, DHCP snooping |
| Operating Temperature | 0 °C to 50 °C |
| Storage Temperature | -40 °C to 70 °C |
| Humidity | 5% to 95% (non-condensing) |
| Cooling | 2 x built-in fans |
| LED Indicators | Power, System, Link/Activity, PoE status per port |
| Rack Mountable | Yes, 1U 19-inch rack mount kit included |
| Cleaning & Maintenance | Wipe with a dry, soft cloth. Do not use liquids or solvents. |
| Safety Certifications | CE, FCC, RoHS |
| Warranty | 3 years limited hardware warranty |
| Repairability | No user-serviceable parts. Contact Hikvision support or authorized service center for repairs. |
Frequently Asked Questions - DS-3E1518P-SI Hikvision
How do I reset the DS-3E1518P-SI to factory defaults?
Press and hold the Reset button (located on the front panel) for at least 10 seconds until all LEDs flash. The switch will reboot with factory settings.
Can I use the switch without any configuration?
Yes, the switch works out of the box as a plug-and-play device. Advanced features require configuration via web interface or CLI.
How do I access the web management interface?
Connect your computer to any port, set your IP to the same subnet (default switch IP: 192.168.1.1), then open a browser and go to http://192.168.1.1. Use default credentials admin/admin.
What is the maximum PoE power per port?
Each PoE+ port can deliver up to 30W (IEEE 802.3at). Total PoE budget is 250W.
Can I mount the switch on a wall?
No, the switch is designed for 19-inch rack mounting. Wall mounting is not supported. Use the included rack ears for installation.
How do I update the firmware?
Download the latest firmware from Hikvision's official website. Log into the web interface, go to 'Maintenance' > 'Firmware Upgrade', select the file and click 'Upgrade'. Do not power off during upgrade.
What should I do if a PoE device is not powering on?
Check the PoE budget (total power used). Ensure the device is connected to a PoE+ port and the cable is Cat5e or higher. If the port LED is off, try a different port. Also verify PoE setting in the management interface.
Does the switch support VLANs?
Yes, it supports 802.1Q VLAN with up to 256 VLANs. You can configure port-based or tagged VLANs via the web interface.
What is the default IP address and login?
Default IP is 192.168.1.1, username admin, password admin. Change the password immediately after first login for security.
How do I know if a port is providing PoE?
Each PoE port has a PoE status LED. Solid green means power is being delivered. Blinking or off indicates no power or fault. You can also check in the web interface under 'PoE' settings.
User questions about DS-3E1518P-SI Hikvision
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Switch in PDF format for free! Find your manual DS-3E1518P-SI - Hikvision and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DS-3E1518P-SI by Hikvision.
USER MANUAL DS-3E1518P-SI Hikvision
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hikvision
Model : DS-3E1518P-SI
Category : Switch