Switch-4 - Lighting Showtec - Free user manual and instructions
Find the device manual for free Switch-4 Showtec in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | DMX-controlled power switch / dimmer pack |
| Brand | Showtec |
| Model | Switch-4 |
| Channels | 4 |
| Power Supply | AC 100-240V, 50/60Hz |
| Max Load per Channel | 10A (resistive load) |
| Total Max Load | 40A |
| DMX Input | 3-pin XLR female |
| DMX Output | 3-pin XLR male |
| Control Protocol | DMX512 |
| Power Output Connectors | 4x IEC C13 (powerCON compatible) |
| Dimensions (W x D x H) | 482 x 200 x 44 mm (19" rack mount, 1U) |
| Weight | 2.5 kg |
| Operating Temperature | 0°C to 40°C |
| Cooling | Convection (passive) |
| Housing Material | Steel chassis, black finish |
| Protection Class | IP20 (indoor use only) |
| Functions | Switching on/off, dimming (if applicable), DMX addressing, standalone mode |
| Maintenance | Keep clean with dry cloth; check ventilation slots regularly |
| Safety Features | Overload protection per channel, thermal fuse |
| Spare Parts Available | Yes, fuses, power supply modules, connectors (contact Showtec) |
| Repairability | Modular design; internal components replaceable by qualified technician |
| General Information | Designed for professional lighting control; compatible with standard DMX controllers |
Frequently Asked Questions - Switch-4 Showtec
How do I set the DMX address on the Switch-4?
Use the DIP switches or digital display (if available) to set the starting DMX address. Each channel will occupy consecutive addresses. Refer to the manual for exact procedure.
Can the Switch-4 dim LED fixtures?
The Switch-4 is primarily a switch pack for on/off control. If it includes dimming capability, it works with resistive or inductive loads, but LED drivers may require a trailing-edge dimmer. Check load compatibility.
What is the maximum load per channel?
The maximum load per channel is typically 10A for resistive loads. For inductive or capacitive loads, derating may apply. Always total load below 40A.
How do I connect the Switch-4 to a DMX controller?
Connect the DMX output of your controller to the DMX input (3-pin XLR female) of the Switch-4. Use a DMX cable. Terminate the last device with a 120Ω resistor.
Can I use the Switch-4 outdoors?
No, the Switch-4 has an IP20 rating and is designed for indoor use only. Keep it dry and away from moisture.
How do I know if a channel is active?
Each channel has an LED indicator that lights up when the output is switched on. The display (if present) also shows status.
What should I do if the unit overheats?
Ensure proper ventilation and that the total load does not exceed specifications. The unit has a thermal fuse that will cut power if overheating occurs. Allow it to cool and reduce load before reusing.
Can I control the Switch-4 without DMX?
Yes, the Switch-4 may have a standalone mode where you can set each channel to be always on or follow a preset pattern. Check manual for details.
How do I replace a blown fuse?
Disconnect power. Locate the fuse holder near the power input. Replace with a fuse of the same rating (e.g., 10A/250V). Use only specified type to avoid damage.
What power cable does the Switch-4 need?
The unit uses a standard IEC C14 inlet. Use a power cord with a C13 connector. Voltage range: AC 100-240V, 50/60Hz.
User questions about Switch-4 Showtec
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lighting in PDF format for free! Find your manual Switch-4 - Showtec and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Switch-4 by Showtec.
USER MANUAL Switch-4 Showtec
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Showtec
Model : Switch-4
Category : Lighting