Xstack DES-3200-10 - NAS D-LINK - Free user manual and instructions
Find the device manual for free Xstack DES-3200-10 D-LINK in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed Ethernet Switch |
| Ports | 8 10/100BASE-TX + 2 10/100/1000BASE-T |
| Switching Capacity | 5.6 Gbps |
| Forwarding Rate | 4.17 Mpps |
| MAC Address Table | 8K entries |
| Dimensions (W x D x H) | 280 x 180 x 44 mm |
| Weight | 1.2 kg |
| Power Supply | 100-240 VAC, 50-60 Hz |
| Power Consumption | 12.5 W |
| Operating Temperature | 0°C to 40°C |
| Management Features | SNMP, CLI, Web GUI, Telnet |
| VLAN Support | Up to 256 VLANs, 802.1Q |
| Quality of Service (QoS) | 802.1p, 4 priority queues |
| Security Features | 802.1X, ACL, Port Security |
| Firmware Upgrade | Via TFTP/Xmodem/Web |
| Cooling | Fanless |
| Mounting | Rack-mountable |
| Standards Compliance | IEEE 802.3, 802.3u, 802.3ab, 802.1D |
| Cleaning Instructions | Use a dry cloth, avoid liquids |
| Repair / Spare Parts | Contact D-Link support; no user-serviceable parts |
Frequently Asked Questions - Xstack DES-3200-10 D-LINK
How do I reset the D-Link Xstack DES-3200-10 to factory defaults?
Press and hold the reset button (located on the front panel) for about 10 seconds until all LEDs blink. This restores factory settings.
What is the default IP address and login for the DES-3200-10?
The default IP address is 10.90.90.90 with subnet mask 255.0.0.0. Default username is 'admin' with no password.
How do I perform a firmware upgrade on the DES-3200-10?
Access the web GUI, go to 'System' > 'Firmware Upgrade', select the firmware file (e.g., .rom) via TFTP or local upload, and apply. The switch will reboot.
Can the DES-3200-10 support VLAN configuration?
Yes, it supports up to 256 VLANs (802.1Q). You can configure port-based or tagged VLANs through the web interface or CLI.
How do I enable port security on the switch?
Go to 'Security' > 'Port Security', enable per port, set maximum MAC addresses, and define allowed MACs. This restricts unauthorized devices.
What should I do if the switch is not powering on?
Check the power cable and ensure the outlet works. Verify the power switch (if any). If still off, contact D-Link support as the power supply may be faulty.
How do I connect to the DES-3200-10 via console cable?
Use an RS-232 cable with DB9 connector to the console port. Settings: 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control.
Does the DES-3200-10 support link aggregation?
Yes, it supports static trunking and LACP (802.3ad) for up to 8 groups, each up to 8 ports.
How do I clean the DES-3200-10?
Turn off the switch, use a soft dry cloth to wipe the case. Do not use any liquids or sprays. Ensure vents are not blocked.
Where can I find spare parts or repair service for the switch?
Spare parts are not user-available. For repairs, contact D-Link authorized service centers. Check warranty status first.
User questions about Xstack DES-3200-10 D-LINK
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your NAS in PDF format for free! Find your manual Xstack DES-3200-10 - D-LINK and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Xstack DES-3200-10 by D-LINK.
USER MANUAL Xstack DES-3200-10 D-LINK
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : D-LINK
Model : Xstack DES-3200-10
Category : NAS