Festo SFAM-62-5000L-TG12-PNLK-PNVBA-M12 - Flow sensor

SFAM-62-5000L-TG12-PNLK-PNVBA-M12 - Flow sensor Festo - Free user manual and instructions

Find the device manual for free SFAM-62-5000L-TG12-PNLK-PNVBA-M12 Festo in PDF.

📄 60 pages English EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs
Notice Festo SFAM-62-5000L-TG12-PNLK-PNVBA-M12 - page 10
10 / 60
Pick your language and provide your email: we'll send you a specifically translated version.
Product TypeFlow sensor
BrandFesto
ModelSFAM-62-5000L-TG12-PNLK-PNVBA-M12
CategoryUncategorized
Measuring Range50...5000 l/min (compressed air)
MediumCompressed air, non-corrosive gases
Operating Voltage18...30 V DC
Output SignalPNP switching output + 4...20 mA analog
Electrical ConnectionM12 plug, 5-pin
Process ConnectionG1/2 (TG12)
Max Pressure10 bar
Operating Temperature0...50 °C
Protection ClassIP65
Dimensions (W x H x D)62 x 45 x 30 mm
Weight150 g
MaterialStainless steel, PBT plastic
DisplayNone (LED indicator for status)
FeaturesIO-Link ready, diagnostic function
MaintenanceClean housing with dry cloth; do not use solvents
Safety NotesObserve voltage limits; use only with compressed air
Spare Parts / RepairabilityNo user-serviceable parts; return to Festo for repair

Frequently Asked Questions - SFAM-62-5000L-TG12-PNLK-PNVBA-M12 Festo

How do I install the SFAM-62-5000L flow sensor?
Mount the sensor in a straight pipe section with at least 10x pipe diameter upstream and 5x downstream. Use the provided G1/2 connections and ensure a leak-free seal.
What is the electrical wiring for the M12 connector?
Pinout: 1 = brown (V+), 2 = white (analog out), 3 = blue (V-), 4 = black (switching output), 5 = gray (IO-Link). Refer to the manual pin diagram.
How can I change the measuring range?
The measuring range is fixed as 50...5000 l/min. For custom scaling, use IO-Link or the analog output with an external controller.
What does the LED indicator mean?
Green LED indicates normal operation. Flashing green = out of range. Red = fault or flow below threshold. Check the manual for details.
Can I use this sensor for liquids?
No. This sensor is designed for compressed air and non-corrosive gases only. Liquids will damage the sensor.
How do I clean the sensor?
Disconnect power. Wipe the housing with a damp cloth. Do not use abrasive cleaners or immerse the sensor.
What is the maximum pressure rating?
The maximum operating pressure is 10 bar. Exceeding this may cause irreversible damage.
How to calibrate the flow sensor?
The sensor is factory calibrated. Field calibration is not required. If needed, use IO-Link to adjust offset or gain.
What are common error codes?
Error codes are communicated via IO-Link. Common: 0x10 (sensor fault), 0x20 (flow out of range). Consult the IO-Link data sheet.
Where can I download the manual?
The manual is available for free at notice-facile.com under the product model SFAM-62-5000L-TG12-PNLK-PNVBA-M12.

User questions about SFAM-62-5000L-TG12-PNLK-PNVBA-M12 Festo

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Flow sensor in PDF format for free! Find your manual SFAM-62-5000L-TG12-PNLK-PNVBA-M12 - Festo and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SFAM-62-5000L-TG12-PNLK-PNVBA-M12 by Festo.

USER MANUAL SFAM-62-5000L-TG12-PNLK-PNVBA-M12 Festo

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Festo

Model : SFAM-62-5000L-TG12-PNLK-PNVBA-M12

Category : Flow sensor