FX-60.2 - Receiver Ashly - Free user manual and instructions
Find the device manual for free FX-60.2 Ashly in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Brand | Ashly |
| Model | FX-60.2 |
| Product Type | Digital Matrix Processor / Receiver |
| Number of Inputs | 6 (balanced line level, XLR) |
| Number of Outputs | 2 (balanced line level, XLR) |
| Signal Processing | 24-bit DSP, 48 kHz sampling rate |
| Frequency Response | 20 Hz - 20 kHz ±0.5 dB |
| Dynamic Range | >110 dB |
| Total Harmonic Distortion + Noise (THD+N) | <0.005% |
| Input Impedance | 20 kΩ balanced |
| Output Impedance | 100 Ω balanced |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Power Consumption | 25 W |
| Dimensions (W x H x D) | 19" x 1.75" x 6.5" (1U rackmount) |
| Weight | 5 lbs (2.3 kg) |
| Connectivity | XLR, RS-232, USB, Ethernet |
| Control Options | Front panel, software, remote control |
| DSP Features | Parametric EQ, crossover, delay, compression, limiting, routing matrix |
| Cooling | Fanless design |
| Compliance | CE, UL |
| Warranty | 3 years |
Frequently Asked Questions - FX-60.2 Ashly
How do I reset the Ashly FX-60.2 to factory defaults?
Press and hold the RESET button on the front panel while powering on the unit. Hold until the display shows 'Factory Reset'. Release and confirm.
What software is available for the FX-60.2?
Ashly provides Protea NE software for configuration and control. It can be downloaded from the Ashly website.
Can the FX-60.2 be controlled via Ethernet?
Yes, the FX-60.2 has an Ethernet port for network control using TCP/IP and Ashly's control protocols.
What is the maximum input level?
The maximum input level is +20 dBu before clipping.
How to update firmware?
Download the latest firmware from Ashly's support page. Connect via USB and use the Protea NE software to upload the firmware file.
Does the FX-60.2 support AES/EBU digital audio?
No, the FX-60.2 only supports analog audio inputs and outputs via balanced XLR connectors.
What is the default IP address?
The default IP address is 192.168.1.100 with subnet mask 255.255.255.0. It can be changed via software.
How do I set up a crossover filter?
Use the Protea NE software to assign a crossover block to an output. Select the filter type (Linkwitz-Riley, Butterworth, etc.) and set the crossover frequency.
My unit won't power on. What should I check?
First, ensure the power cable is securely connected and the outlet provides 100-240 VAC. Check the fuse on the IEC inlet; replace if blown (type F 0.5A 250V).
How to clean the FX-60.2?
Disconnect power. Use a soft, dry cloth to gently wipe the front panel and chassis. Do not use liquids or abrasive cleaners.
User questions about FX-60.2 Ashly
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual FX-60.2 - Ashly and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FX-60.2 by Ashly.
USER MANUAL FX-60.2 Ashly
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Ashly
Model : FX-60.2
Category : Receiver