Limelight Par L - Lamp Elation - Free user manual and instructions
Find the device manual for free Limelight Par L Elation in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Par Light |
| Brand | Elation |
| Model | Limelight Par L |
| Light Source | LED (RGBA or RGBW, 30W per LED) |
| Power Consumption | 200W |
| Dimensions (W x D x H) | 12.0 x 10.0 x 10.0 in |
| Weight | 6.0 lbs |
| Beam Angle | 25° |
| DMX Channels | 4, 5, or 8 selectable |
| Control Protocol | DMX512 |
| Operating Modes | DMX, Master/Slave, Sound Active, Auto Run |
| Strobe Rate | 0-20 Hz |
| Dimmer | 0-100% linear |
| Color Mixing | RGB/RGBA color mixing via DMX |
| Safety Features | Auto voltage sensing, overheat protection, safety cable attachment point |
| Cleaning | Wipe with dry cloth; use compressed air for vents |
| Spare Parts | Contact Elation support for replacement LEDs or power supply |
| Voltage Rating | 100-240V AC, 50-60 Hz |
| Housing Material | Aluminum die-cast |
| IP Rating | IP20 (indoor use) |
| Certifications | ETL, CE |
Frequently Asked Questions - Limelight Par L Elation
How do I set the DMX address on the Limelight Par L?
Use the control buttons on the rear panel to navigate to the DMX address menu. Set the address using the up/down buttons. Ensure the fixture is in DMX mode.
What is the maximum number of units in a master/slave chain?
You can connect up to 32 units in a daisy-chain for master/slave operation. Use 3-pin XLR cables.
How do I clean the lens of the fixture?
Disconnect power. Use a soft, dry cloth to wipe the lens. Avoid abrasive cleaners. For stubborn dirt, lightly dampen the cloth with water.
The light is not responding to DMX. What should I check?
Verify the DMX cable is securely connected. Ensure the fixture's DMX address matches the controller. Check that the terminator is installed on the last fixture. Test with a known working cable.
Can I use the Limelight Par L outdoors?
No, this fixture is rated IP20 for indoor use only. Exposure to moisture or dust may cause damage.
How do I replace a burned-out LED?
LED replacement should be performed by a qualified technician. Contact Elation service for instructions and spare parts. Do not attempt to open the housing yourself.
What power cord does the fixture require?
The fixture uses a standard IEC power cord. Input voltage is 100-240V AC, 50-60 Hz. Use the cord provided with the unit.
How can I update the firmware?
Firmware updates are not user-serviceable. Contact Elation support to check if updates are available and how to proceed.
What is the strobe effect and how do I control it?
The strobe effect quickly flashes the light at a rate of 0-20 Hz. You can control it via a DMX channel assigned to strobe speed. In standalone mode, use the menu to enable sound-active strobe.
The fixture overheats and shuts off. What can I do?
Ensure proper ventilation around the fixture. Check that the fan (if any) is not blocked. Reduce ambient temperature. The fixture will reset once cooled. If persists, contact support.
User questions about Limelight Par L Elation
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lamp in PDF format for free! Find your manual Limelight Par L - Elation and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Limelight Par L by Elation.
USER MANUAL Limelight Par L Elation
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Elation
Model : Limelight Par L
Category : Lamp