SRP-S300II - Printer Bixolon - Free user manual and instructions
Find the device manual for free SRP-S300II Bixolon in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Thermal Receipt Printer |
| Model | SRP-S300II |
| Print Method | Direct Thermal |
| Print Resolution | 203 dpi (8 dots/mm) |
| Print Speed | Up to 250 mm/s |
| Paper Width | 80 mm (max 82.5 mm) |
| Paper Roll Diameter | Up to 83 mm |
| Interfaces | USB 2.0, Serial (RS-232), Ethernet |
| Emulations | ESC/POS, Star, Bixolon |
| Auto Cutter | Yes, full cut with partial cut option |
| Barcode Support | 1D: UPC-A/E, EAN-13/8, Code 39/128, etc.; 2D: QR, PDF417, Data Matrix |
| Power Supply | 24 VDC, 2.5 A (external adapter) |
| Dimensions (W x D x H) | 147 x 200 x 148 mm |
| Weight | 1.5 kg |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 10% to 90% (non-condensing) |
| MTBF | 1,500,000 hours (print head) |
| Maintenance | Clean print head and platen roller with isopropyl alcohol |
| Safety Certifications | FCC, CE, UL, RoHS |
| Included Accessories | Power adapter, USB cable, quick start guide |
Frequently Asked Questions - SRP-S300II Bixolon
How do I load paper into the Bixolon SRP-S300II?
Open the paper cover, insert the roll with the thermal side facing down, pull a small amount of paper out, and close the cover. The printer will automatically feed the paper.
What is the maximum paper roll diameter?
The SRP-S300II accommodates paper rolls up to 83 mm in diameter.
How do I change the printer's baud rate?
You can adjust baud rate, parity, and other serial settings via the DIP switches located inside the paper compartment or by sending configuration commands.
Why is the printer not printing?
Check if the power is on, the paper is loaded correctly, the interface cable is connected, and the printer is not in error state (e.g., cover open, paper jam). Try printing a self-test by holding the feed button while powering on.
How do I clean the print head?
Turn off the printer and unplug it. Open the cover, remove paper, and gently wipe the thermal print head with a cotton swab moistened with isopropyl alcohol. Allow to dry before use.
What interfaces does the SRP-S300II support?
It supports USB 2.0, RS-232 serial, and Ethernet (wired network).
Can I print barcodes and QR codes?
Yes, the printer supports many 1D barcodes (UPC, EAN, Code 39/128, etc.) and 2D codes (QR, PDF417, Data Matrix) via ESC/POS commands.
How do I perform a printer self-test?
Hold the FEED button while turning on the power. Release the button after the printer starts printing the self-test page. This prints configuration and print quality information.
What is the power consumption of the printer?
The printer uses a 24 VDC, 2.5 A external power supply. Typical consumption is about 60 W during printing and much lower in standby.
How do I reset the printer to factory defaults?
Turn off the printer. While holding the FEED and ERROR buttons (if available) together, turn on the power. Alternatively, send a reset command via software or adjust DIP switches.
User questions about SRP-S300II Bixolon
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Printer in PDF format for free! Find your manual SRP-S300II - Bixolon and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SRP-S300II by Bixolon.
USER MANUAL SRP-S300II Bixolon
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Bixolon
Model : SRP-S300II
Category : Printer