ZQ510 - Printer ZEBRA - Free user manual and instructions
Find the device manual for free ZQ510 ZEBRA in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Mobile Thermal Printer |
| Model | ZQ510 |
| Brand | Zebra |
| Print Technology | Direct Thermal |
| Print Resolution | 203 dpi (8 dots/mm) |
| Print Speed | Up to 4 ips (102 mm/s) |
| Max Print Width | 2.2 inches (56 mm) |
| Max Media Width | 2.2 inches (56 mm) |
| Media Roll Diameter | Max 1.5 inches (38 mm) |
| Connectivity | Bluetooth 4.0, Wi-Fi (optional), USB 2.0 |
| Battery | Lithium-ion, 7.4V, 2400 mAh |
| Battery Life | Up to 12 hours |
| Dimensions (W x D x H) | 4.6 x 2.8 x 1.3 in (117 x 71 x 33 mm) |
| Weight | 0.5 lbs (227 g) |
| Operating Temperature | 14°F to 122°F (-10°C to 50°C) |
| Drop Spec | 5 ft (1.5 m) to concrete |
| IP Rating | IP54 |
| Languages | ZPL, EPL, CPCL |
| Memory | 32 MB SDRAM, 64 MB Flash |
| Display | Two buttons, LEDs |
| Accessories Included | Belt clip, charger, USB cable |
| Cleaning | Use cleaning pen for printhead; replace when worn |
| Safety Certifications | FCC, CE, UL; avoid moisture |
| Repairability | User-replaceable printhead and battery |
Frequently Asked Questions - ZQ510 ZEBRA
How do I connect the ZQ510 to Bluetooth?
Ensure the printer is powered on, then pair via your device's Bluetooth settings. The default PIN is 0000. For detailed steps, refer to the pairing section in the manual.
How to load paper into the ZQ510?
Open the printer's cover by pressing the release button. Insert the paper roll with the print side facing up. Close the cover until it clicks. The printer auto-feeds the paper.
How to clean the printhead of the ZQ510?
Use a Zebra-approved cleaning pen or lint-free swab with isopropyl alcohol. Always turn off the printer and wait for the printhead to cool before cleaning.
What type of paper does the ZQ510 use?
It uses direct thermal paper rolls with a maximum width of 2.2 inches (56 mm). Recommended paper: Z-Ultimate 2500 series or equivalent.
How to change the battery on the ZQ510?
Turn off the printer. Slide the battery latch to unlock, remove the old battery, and insert a new lithium-ion battery (7.4V, 2400 mAh) until it clicks.
The printer is not printing. What should I do?
Check battery level, ensure paper is loaded correctly, and verify Bluetooth connection. If the LED is red, perform a cold reset by holding the power button for 10 seconds.
How to reset the ZQ510 to factory defaults?
Turn off the printer. Press and hold the Feed and Power buttons simultaneously for 5 seconds. The printer will reset and print a configuration label.
How to update firmware on the ZQ510?
Download the latest firmware from the Zebra website. Use Zebra Setup Utilities or send the file via Bluetooth/USB. Detailed instructions are in the manual.
What is the maximum print speed of the ZQ510?
The maximum print speed is 4 inches per second (102 mm/s) at 203 dpi resolution.
Is the ZQ510 waterproof?
It is not fully waterproof, but it has an IP54 rating meaning it is dust-resistant and protected against water splashes from any direction.
User questions about ZQ510 ZEBRA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Printer in PDF format for free! Find your manual ZQ510 - ZEBRA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ZQ510 by ZEBRA.
USER MANUAL ZQ510 ZEBRA
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ZEBRA
Model : ZQ510
Category : Printer