A+ Server 4023S-TRT - Server Supermicro - Free user manual and instructions
Find the device manual for free A+ Server 4023S-TRT Supermicro in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rackmount Server |
| Form Factor | 4U |
| Processor Support | Dual AMD EPYC 7003 Series |
| Memory Support | Up to 2TB DDR4 ECC Registered, 32 DIMM slots |
| Drive Bays | Up to 24x 2.5” or 12x 3.5” hot-swap SATA/SAS |
| Expansion Slots | 7 PCIe 4.0 x16, 1 PCIe 4.0 x8 |
| Network Connectivity | Dual 10GBase-T, optional OCP 3.0 |
| Power Supply | 2x 1600W Redundant (80+ Platinum) |
| Dimensions (WxDxH) | 17.2 x 30.5 x 6.9 inches (437 x 775 x 176 mm) |
| Weight | Approximately 85 lbs (38.6 kg) with drives |
| Cooling | 6x Hot-swap PWM fans, optimal airflow |
| Management | IPMI 2.0 with SuperDoctor 5 |
| RAID Support | Hardware RAID via Broadcom 3908 or similar |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Certifications | FCC, CE, RoHS |
| Cleaning Instructions | Use compressed air for dust; avoid liquids. |
| Safety Notices | Install in a rack with proper grounding; disconnect power before service. |
| Spare Parts | PSU, fan modules, drive trays, rails available from Supermicro. |
| Warranty | 3 years limited (parts & labor) |
| Included Accessories | Rack mount kit, power cords, quick reference guide |
Frequently Asked Questions - A+ Server 4023S-TRT Supermicro
How do I install the server in a rack?
Use the included rack mount kit. Attach the inner rails to the server and outer rails to the rack, then slide the server in. Ensure proper cable management and ventilation.
What CPUs are compatible with this server?
The Supermicro A+ Server 4023S-TRT supports dual AMD EPYC 7003 (Milan) series processors. Check the manual for specific model support.
How much memory can I install?
It supports up to 2TB of DDR4 ECC Registered memory across 32 DIMM slots (16 per CPU). Use 64GB or 128GB modules for maximum capacity.
Can I use 3.5-inch hard drives?
Yes, the server supports up to 12x 3.5-inch hot-swap SATA/SAS drives. Alternatively, use 24x 2.5-inch drives with an optional backplane.
How do I access the IPMI remote management?
Connect to the dedicated IPMI port (shared with LAN1). Default IP is 192.168.0.1; use a browser or Supermicro's SuperDoctor 5 software.
What should I do if the system doesn't power on?
Check power cables and PSU status LEDs. Ensure both PSUs are connected and switches are on. If using a UPS, verify its output. Reset IPMI if necessary.
How do I configure RAID?
Enter the RAID BIOS during boot (Ctrl+R or Ctrl+Y). Create a RAID array using the onboard Broadcom controller. Refer to the manual for detailed steps.
What is the best way to clean the server?
Power off and unplug the server. Use compressed air to blow dust from fans, heatsinks, and filters. Avoid vacuum cleaners and liquid cleaners.
Can I install a GPU?
Yes, the server has 7 PCIe 4.0 x16 slots. It supports full-length, double-width GPUs, but ensure power and cooling are adequate.
Where can I find replacement parts?
Genuine Supermicro parts are available through authorized distributors or the Supermicro online store. Spare part numbers are in the manual.
User questions about A+ Server 4023S-TRT Supermicro
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual A+ Server 4023S-TRT - Supermicro and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. A+ Server 4023S-TRT by Supermicro.
USER MANUAL A+ Server 4023S-TRT Supermicro
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Supermicro
Model : A+ Server 4023S-TRT
Category : Server