Rebel-30 Head - Guitar amp Egnater - Free user manual and instructions
Find the device manual for free Rebel-30 Head Egnater in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Guitar Amplifier Head |
| Brand | Egnater |
| Model | Rebel-30 Head |
| Category | Tube Guitar Amplifier |
| Power Output | 30 Watts (switchable to 1, 5, 15, and 30 watts) |
| Preamp Tubes | 3x 12AX7 |
| Power Tubes | 2x 6V6 |
| Channels | 2 (Clean, Overdrive) |
| Controls | Gain, Volume, Treble, Mid, Bass, Reverb, Master, and Channel Switch |
| Reverb | Built-in Spring Reverb |
| Effects Loop | Series Effects Loop (Send/Return) |
| Speaker Output | 1x 8-ohm and 2x 16-ohm jacks |
| Input Impedance | 1M Ohm |
| Dimensions (H x W x D) | 8.5 x 18 x 8.5 inches |
| Weight | 24 lbs (10.9 kg) |
| Power Supply | 120V/240V selectable, 50-60Hz |
| Fuse | 1A 250V Slow Blow |
| Construction | Steel chassis, Vinyl-covered plywood cabinet |
| Warranty | 3 years (limited) |
Frequently Asked Questions - Rebel-30 Head Egnater
What tubes does the Egnater Rebel-30 Head use?
The Egnater Rebel-30 Head uses 3x 12AX7 preamp tubes and 2x 6V6 power tubes. It can also accept EL84 tubes but may require rebiasing.
How do I change the power tubes on the Rebel-30?
Power tubes are located under the top chassis. Always unplug the amplifier and let it cool down. Remove the back panel, gently pull out the old tubes, and insert new ones. The amp has a fixed bias but it's recommended to have a technician check bias when changing tube types.
Does the Rebel-30 need to be biased?
Yes, if you change tube types (e.g., from 6V6 to EL84) or mix brands. The Rebel-30 features a partial cathode bias that allows for tube swaps without immediate biasing, but for optimal performance and tube life, professional biasing is advised.
Can I use the Rebel-30 without a speaker cabinet?
No, never operate a tube amplifier without a speaker load connected. The Rebel-30 requires a minimum of 8 ohms to prevent damage to the output transformer.
How do I clean the amp?
Unplug the amp and use a soft dry cloth to wipe the exterior. For the chassis, use compressed air to remove dust. Avoid using liquids or abrasive cleaners. The tube sockets can be cleaned with a contact cleaner if needed.
What is the power scaling feature?
The Rebel-30 has a power scaling knob that allows you to reduce the power output from 30 watts down to 1 watt. This lets you achieve overdrive at lower volumes, perfect for home or studio use.
How do I use the effects loop?
Connect your effect pedal's output to the 'Send' jack and input from the pedal to the 'Return' jack. The loop is series, so all signal passes through the pedal. Adjust pedal levels to match the loop's signal strength.
What type of reverb does the Rebel-30 have?
It has a built-in spring reverb with a dedicated reverb control. The reverb is footswitchable and adds depth to both clean and overdrive channels.
Can I use a footswitch with the Rebel-30?
Yes, the Rebel-30 has a 1/4-inch footswitch jack for channel switching and reverb on/off. You can use a standard two-button footswitch (like Egnater FS-2 or similar).
What causes the fuse to blow frequently?
A blown fuse can indicate a bad power tube, a short in the circuit, or a faulty rectifier. If the fuse blows repeatedly, do not replace with a higher rating. Consult a qualified technician to diagnose the issue.
User questions about Rebel-30 Head Egnater
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Guitar amp in PDF format for free! Find your manual Rebel-30 Head - Egnater and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Rebel-30 Head by Egnater.
USER MANUAL Rebel-30 Head Egnater
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Egnater
Model : Rebel-30 Head
Category : Guitar amp