ARMOR AR2400.4 - Hi-Fi System BOSS - Free user manual and instructions
Find the device manual for free ARMOR AR2400.4 BOSS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 4-Channel Car Amplifier |
| RMS Power (4 ohms) | 4 x 200 Watts |
| RMS Power (2 ohms) | 4 x 400 Watts |
| Peak Power | 4 x 800 Watts |
| Frequency Response | 20 Hz - 20 kHz |
| Signal-to-Noise Ratio | ≥ 100 dB |
| Total Harmonic Distortion | < 0.01% |
| Input Sensitivity | 200 mV - 6 V |
| Dimensions (L x W x H) | 15.6 x 2.4 x 11.8 inches |
| Weight | 8.2 lbs |
| Power Supply | 12V DC (10-16V) |
| Fuse Rating | 4 x 30A (ATC) |
| Key Features | MOSFET power supply, variable crossover, subsonic filter, bass boost, remote level control, 2-ohm stable |
| Protection Circuits | Short circuit, thermal, over-voltage, under-voltage |
| Channel Configuration | 4 channels (bridgeable to 2/3/4) |
| Crossover Type | Variable low-pass/high-pass (50-200 Hz) and full-range |
| Bass Boost | 0-12 dB at 45 Hz |
| Remote Subwoofer Level Control | Yes (included) |
| Input Impedance | 10 kΩ |
| Recommended Speaker Impedance | 4-8 ohms (per channel), 2 ohms (bridged) |
| Certifications | CE, RoHS |
| Warranty | 1 year |
| Cleaning Instructions | Wipe with a dry, soft cloth. Avoid solvents. |
| Repair/Replacement Parts | Contact BOSS Audio support or authorized dealer |
Frequently Asked Questions - ARMOR AR2400.4 BOSS
What is the RMS power rating per channel on the BOSS ARMOR AR2400.4?
At 4 ohms, each channel delivers 200 watts RMS. At 2 ohms, it delivers 400 watts RMS per channel.
Can I bridge channels on the ARMOR AR2400.4?
Yes, you can bridge channels 1&2 and 3&4. Bridged at 4 ohms, each pair delivers 800 watts RMS.
What gauge power wire should I use for this amplifier?
For optimal performance, use 4 AWG power and ground wire. Ensure the wire is fused within 18 inches of the battery.
Does the ARMOR AR2400.4 have a built-in crossover?
Yes, it features a variable low-pass and high-pass crossover (50-200 Hz) and can be set to full-range mode.
What type of power supply does this amplifier use?
It uses a MOSFET PWM (Pulse-Width Modulated) power supply for high efficiency and stable output.
How do I set the gain on the ARMOR AR2400.4?
Turn the gain to minimum, play a test tone at 50-75% volume, then slowly increase gain until distortion is heard, then back off slightly. Use a digital multimeter for accuracy.
What is the recommended speaker impedance for bridged mode?
When bridging two channels, the minimum impedance is 4 ohms. Never bridge to a 2-ohm load as it may cause overheating.
Does the amplifier have thermal or short circuit protection?
Yes, it includes thermal, short circuit, over-voltage, and under-voltage protection to safeguard the amplifier and your electrical system.
What remote level control is included with the ARMOR AR2400.4?
A wired remote subwoofer level control is included, allowing you to adjust bass output from the driver's seat.
How do I clean and maintain the amplifier?
Disconnect power before cleaning. Wipe the exterior with a soft, dry cloth. Avoid using liquids or solvents. Ensure ventilation slots are clear of dust.
User questions about ARMOR AR2400.4 BOSS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Hi-Fi System in PDF format for free! Find your manual ARMOR AR2400.4 - BOSS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ARMOR AR2400.4 by BOSS.
USER MANUAL ARMOR AR2400.4 BOSS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : BOSS
Model : ARMOR AR2400.4
Category : Hi-Fi System