AD22S - Processor Rane - Free user manual and instructions
Find the device manual for free AD22S Rane in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Professional Audio Digital Signal Processor |
| Model | AD22S |
| Brand | Rane |
| Channels | 2 Inputs, 6 Outputs |
| Audio Conversion | 24-bit / 48 kHz |
| Frequency Response | 20 Hz – 20 kHz (±0.5 dB) |
| Dynamic Range | > 110 dB (A-weighted) |
| THD+N | < 0.005% at 1 kHz, +20 dBu |
| Input Impedance | 20 kΩ (balanced) |
| Output Impedance | 100 Ω (balanced) |
| Maximum Input Level | +24 dBu |
| Maximum Output Level | +24 dBu |
| Power Supply | 100-240 VAC, 50/60 Hz, 30 W |
| Dimensions (H x W x D) | 1.75" x 19" x 6.5" (44 x 483 x 165 mm) |
| Weight | 5.5 lb (2.5 kg) |
| Mounting | 19" rack mount, 1U |
| Cooling | Fanless, convection cooled |
| Primary Functions | EQ, crossover, delay, compression, limiting, signal routing |
| Control Interface | Ethernet (RJ-45) for software control |
| Software | RaneWARE (compatible with Windows) |
| Maintenance | Clean exterior with dry cloth; no user-serviceable parts inside |
| Safety | ESD and overvoltage protection; meets CE, UL standards |
| Spare Parts & Repairability | Contact Rane authorized service centers; no user-replaceable parts |
| Warranty | 2 years limited (check local regulations) |
Frequently Asked Questions - AD22S Rane
How do I connect the AD22S to my audio system?
Use balanced XLR cables for inputs and outputs. Connect your source to Input 1 and Input 2. Outputs 1-6 can be routed to amplifiers or other devices. Power on after all connections are made.
Can I control the AD22S without a computer?
No, the AD22S requires a computer running RaneWARE software via Ethernet for configuration and control. There are no front panel controls.
What is the default IP address of the AD22S?
The factory default IP address is 192.168.1.50 with subnet mask 255.255.255.0. You can change it via RaneWARE.
How do I update the firmware?
Download the latest firmware from Rane's website. Connect the AD22S to your computer via Ethernet, open RaneWARE, and use the Firmware Update tool. Do not power off during update.
What are the LED indicators on the front panel?
There is a Power LED (green) and a Status LED (green/red). A steady green Status indicates normal operation. Flashing red indicates an error or overload.
Can I use unbalanced cables?
It is recommended to use balanced cables for best noise rejection. If using unbalanced, keep cable runs short and use a balun if needed.
How do I reset the AD22S to factory defaults?
Power off the unit. Press and hold the Reset button (inside the rear panel hole) while powering on. Hold for 5 seconds until the Status LED flashes rapidly.
What is the maximum number of presets?
The AD22S can store up to 100 presets in internal memory. They can be recalled via software or automation commands.
Can I daisy-chain multiple AD22S units?
Yes, you can connect multiple units via Ethernet switch. Each unit must have a unique IP address. All units can be managed from a single RaneWARE session.
How do I clean the AD22S?
Disconnect power. Use a soft, dry cloth to wipe the exterior. Do not use liquids or cleaners. Ensure ventilation slots are free of dust.
User questions about AD22S Rane
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Processor in PDF format for free! Find your manual AD22S - Rane and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AD22S by Rane.
USER MANUAL AD22S Rane
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Rane
Model : AD22S
Category : Processor