DMX-BRANCH/4 - PCI card Elation - Free user manual and instructions
Find the device manual for free DMX-BRANCH/4 Elation in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | DMX Splitter / Amplifier PCI Card |
| Brand | Elation |
| Model | DMX-BRANCH/4 |
| Category | PCI Card |
| DMX Input | 1 x 5-pin XLR (female) |
| DMX Outputs | 4 x 5-pin XLR (male), optically isolated |
| Power Supply | Powered via PCI bus (5V DC) |
| Power Consumption | 2.5 W |
| Dimensions (PCB only) | 120 x 80 x 20 mm (4.7 x 3.1 x 0.8 in) |
| Weight | 100 g (0.22 lbs) |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Compliance | CE, RoHS |
| Functions | DMX512 signal splitting and amplification, line isolation |
| Installation | Plug-and-play in standard PCI slot (32-bit, 3.3V/5V) |
| Maintenance | Keep clean and dry; avoid static discharge |
| Safety | Use in shielded enclosure; disconnect power before servicing |
| Spare Parts | Contact Elation Professional for replacement XLR connectors |
| Reparability | Modular design; limited user-serviceable parts |
| Warranty | 2 years |
Frequently Asked Questions - DMX-BRANCH/4 Elation
What is the Elation DMX-BRANCH/4?
The DMX-BRANCH/4 is a PCI card that functions as a DMX512 splitter and amplifier, allowing one DMX input to be distributed to four optically isolated outputs.
How do I install the DMX-BRANCH/4?
Power off your computer, open the case, insert the card into an available PCI slot, secure it with the screw, and close the case. No additional drivers are required; it is plug-and-play.
What type of connectors does it use?
The card has one 5-pin XLR female input and four 5-pin XLR male outputs. Use standard DMX cables.
Is the DMX-BRANCH/4 compatible with 3-pin DMX?
The card uses 5-pin XLR connectors, but you can use adapters (5-pin to 3-pin) if your fixtures have 3-pin connectors. Note that pins 1, 2, and 3 are used; pins 4 and 5 are reserved.
Does the card require external power?
No, it is powered directly from the PCI bus (5V DC). No external power supply is needed.
How many DMX devices can I connect to each output?
Each output can drive up to 32 DMX devices (standard load). For longer runs or more devices, use additional splitters or amplifiers.
What is DMX termination and do I need it?
DMX termination is a 120-ohm resistor placed at the last fixture to prevent signal reflection. The card does not include built-in termination; terminate the last fixture on each output line.
Can I use the card with lighting software?
Yes, the card acts as a passive splitter; it does not interface with software. Connect your DMX controller (e.g., USB DMX interface) to the input, and the outputs go to fixtures.
What is the maximum cable length per output?
The maximum recommended DMX cable length from the card to the last fixture is 300 meters (1000 feet) for reliable data transmission.
How do I clean the card?
Use compressed air to remove dust from the PCI contacts and connectors. Avoid liquid cleaners. Handle card by edges to prevent static damage.
User questions about DMX-BRANCH/4 Elation
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your PCI card in PDF format for free! Find your manual DMX-BRANCH/4 - Elation and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DMX-BRANCH/4 by Elation.
USER MANUAL DMX-BRANCH/4 Elation
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Elation
Model : DMX-BRANCH/4
Category : PCI card