One 2 Mini - Keyboard Ducky - Free user manual and instructions

Product Type	Mechanical Keyboard
Form Factor	60% (61 keys)
Dimensions (W x D x H)	302 x 108 x 40 mm
Weight	Approx. 600 g
Connection	USB Type-C (detachable cable)
Switch Compatibility	Cherry MX switches (Blue, Brown, Red, Silver, etc.)
Keycap Material	PBT double-shot
Backlighting	RGB per-key LED (multiple modes)
N-Key Rollover	Full N-key rollover
Programmable	Yes (via DIP switches and hardware macros)
Polling Rate	1000 Hz
Compatible Systems	Windows, macOS, Linux
Power Source	USB bus power (5V, 500mA max)
Cleaning Instructions	Unplug keyboard; use compressed air and soft brush; avoid liquids.
Safety Warnings	Do not expose to moisture; keep away from heat sources.
Spare Parts Available	Keycaps, switches, USB cable, case components
Warranty	1 year limited (varies by region)

Frequently Asked Questions - One 2 Mini Ducky

How do I change the keycaps on my Ducky One 2 Mini?

Use a keycap puller to gently remove the keycaps. Align the new keycaps with the stem and press down firmly. Make sure to check the orientation for stabilizers (e.g., spacebar).

Can I program macros on the One 2 Mini?

Yes, the One 2 Mini supports hardware macros. Press Fn + Ctrl + Win to enter macro recording mode, then assign keys. Refer to the manual for detailed steps.

What switches are available for this keyboard?

The Ducky One 2 Mini is available with various Cherry MX switches: Blue (clicky), Brown (tactile), Red (linear), and Silver (linear, low actuation).

How do I clean my Ducky One 2 Mini?

Unplug the keyboard. Use compressed air to remove debris between keys. For deeper cleaning, remove keycaps and wipe the plate with a slightly damp cloth. Avoid liquids near the PCB.

Is the USB cable detachable?

Yes, the One 2 Mini uses a standard USB Type-C to USB-A cable. It is detachable, so you can replace it if needed.

Does the keyboard work with game consoles?

The One 2 Mini is primarily designed for PC (Windows, macOS, Linux). Some consoles may work via USB OTG, but full functionality (e.g., RGB software) is not guaranteed.

How do I reset the keyboard to factory settings?

Press and hold both Left Win and Right Win keys for 3 seconds until the LEDs flash. This resets all settings including macros and lighting.

What is the warranty period?

The Ducky One 2 Mini typically comes with a 1-year limited warranty against manufacturing defects. Warranty may vary by region; check with your retailer.

Can I replace the switches without soldering?

The standard One 2 Mini is not hot-swappable. Switches are soldered to the PCB. However, Ducky offers a hot-swappable version (One 2 Mini SF) separately.

How do I adjust the RGB lighting?

Use the Fn key combined with number keys (e.g., Fn + 1-7 for preset modes) or arrow keys to change brightness and speed. Custom configurations require Ducky's software on PC.

USER MANUAL One 2 Mini Ducky

Mini

User Manual

MECHA

ONE

目錄

Ducky Mecha Mini/ One 2 Mini 規格與特色 1,2

標準層鍵盤配置圖 3

Fn 層鍵盤配置圖 4

Fn+Alt層鍵盤配置圖 5

RGB 燈光操作模式 6

RGB 記憶區域背光 8

Ducky 遊戲互動模式 9

多媒體功能 10

設定 Debounce Time 10

行動電源Demo模式 11

店家櫥窗Demo模式 11

回復出廠設定 12

Windows Lock功能 12

DIP指撥開關功能 13

Ducky Mecha/ One 2 Mini Macro 14

Ducky Mecha/ One 2 Mini Macro 基本快捷鍵功能 15

Ducky Mecha/ One 2 Mini Macro 設定區域的範圍 16

Ducky Mecha/ One 2 Mini Macro 指定「多媒體鍵功能」設定輸入指令 17

Ducky Mecha/ One 2 Mini Macro 指定「鍵盤按鍵功能」設定輸入指令 18

Ducky Mecha/ One 2 Mini Macro Windows 常見功能快捷鍵 19

Ducky Mecha/ One 2 Mini Macro 使用範例 20

Content

Ducky Mecha Mini/ One 2 Mini specs & features 21, 22

Standard layer keyboard configuration diagram 23

Fn layer keyboard configuration diagram 24

Fn+Alt layer keyboard configuration diagram 25

RGB Backlit modes 26

RGB zone customization modes 28

Ducky Gaming Interaction mode 28

Multimedia function 29

Debounce time setting 29

Demo mode 30

Display mode 30

Reset to factory defaults 31

Windows key lock feature 32

DIP switch functions 33

Ducky Mecha/ One 2 Mini Macro 34

Ducky Mecha/ One 2 Mini Macro hotkeys function 35

Ducky Mecha/ One 2 Mini Macro setting section 36

Ducky Mecha/ One 2 Mini Macro multimedia function keys 37

Ducky Mecha/ One 2 Mini Macro keyboard button function keys 38

Ducky Mecha/ One 2 Mini Macro Windows common function keys 39

Ducky Mecha/ One 2 Mini Macro set up example 40

Ducky Mecha Mini

Mecha Mini 版本

產品規格：

結構：機械式結構

軸：Cherry MX 機械軸

燈光：RGB

鍵帽材質：PBT 或 ABS

印字技術：二色成型或雷雕

產地：台灣

尺寸：295×108×40mm

重量：826g

重點特色：

採用奈米塗層鋁合金機身鋅合金腳架

Ducky One 2 Mini

RGB LED 燈版本

產品規格：

Ducky Mecha/ One 2 Mini

鍵盤配置圖，以美規為範例

標準層

Ducky Mecha/ One 2 Mini

鍵盤配置圖，以美規為範例

Fn層

Ducky Mecha/ One 2 Mini

鍵盤配置圖，以美規為範例

Fn + Alt層

RGB燈光操作模式

Fn + Alt + T

第一次：波浪模式（預設）

第二次：循環變色模式

第三次：雨滴模式

第四次：圆形漣漪模式

第五次：隨機單點亮模式

第六次：單點亮（可設定顏色）

第七次：光暈模式（可設定顏色）

第八次：單色呼吸模式（可設定顏色）

RGB 記憶區域背光

RGB 記憶區域背光

操作過程

Ducky遊戲互動模式

鍵位切換與 DIP 指撥開關功能

鍵位切換功能

1. 適用按鍵: Fn/Alt/Ctrl/Windows/Caps lock鍵
2. 操作方式:

DIP 指撥開關功能

DIP1	OFF(預設)	ON
	Windows鍵功能ON	Windows鍵功能OFF
DIP2	OFF(預設)	ON
	任意全鍵輸出	任意6鍵輸出
DIP3	OFF(預設)	ON
	Ducky VID	可自定VID
DIP4	OFF(預設)	ON
	標準鍵盤模式	櫥窗展示模式

Ducky Mecha/ One 2 Mini

Step1. 選取要錄製的Profile

Ducky Mecha/ One 2 Mini

基本快捷鍵功能

Ducky Mecha/ One 2 Mini

設定區域的範圍

Ducky Mini Macro可設定之鍵盤層

註：

Ducky Mecha/ One 2 Mini

指定「多媒體鍵功能」設定輸入指令

Ducky Mecha/ One 2 Mini

指定「鍵盤按鍵功能」設定輸入指令

Ducky Mecha/ One 2 Mini

Windows 常見功能快捷鍵

Ducky Mecha/ One 2 Mini

使用範例

Type : Mechanical keyboard
Switch : Cherry MX switches
LED : RGB LED
Keycap material : PBT or ABS
Printing method : Double-shot
or Laser Engraved
Origin of production : Taiwan
Size : 295 x 108 x 40 mm
Weight: 826g

Features :

Aluminum case with nano-coating and Zinc alloy stands
Cherry MX key switches for quality assurance
Various RGB LED lighting modes which includes brand new game modes
True USB Type-C interface, compatible with all Type-C devices
Provides mouse functions for a convenient experience
Miniature yet packed with features
Supports Ducky Macro through hardware, personalize functions as you like
RGB version with Four-layer PCB featured, insisting on using the best specs
Products with PBT Double-shot Seamless keycaps, providing the perfectly exceptional typing experience

Ducky One 2 Mini

RGB LED version

Specification

Type : Mechanical keyboard
Switch : Cherry MX switches
LED : RGB LED
Keycap material : PBT or ABS
Printing method : Double-shot or Lazer Engrave
Origin of production : Taiwan
Size : 302 x 108 x 40 mm
Weight: 590g

Features :

Cherry MX key switches for quality assurance
Various RGB LED lighting modes which includes brand new game modes
True USB Type-C interface, compatible with all Type-C devices
Provides mouse functions for a convenient experience
Miniature yet packed with features
Supports Ducky Macro through hardware, personalize functions as you like
RGB version with Four-layer PCB featured, insisting on using the best specs
Products with PBT Double-shot Seamless keycaps, providing the perfectly exceptional typing experience

Ducky Mecha/ One 2 Mini

Keyboard configuration diagram, US layout used as example

Standard layer

Ducky Mecha/ One 2 Mini

Keyboard configuration diagram, US layout used as example

Fn layer

Ducky Mecha/ One 2 Mini

Keyboard configuration diagram, US layout used as example

Fn + Alt layer

RGB Backlit Modes

Fn + Alt + T	First mode: Wave mode (Default)	Seventh mode: Halo mode
	Second mode: Color Cycle mode	Eighth mode: Breathe mode
	Third mode: Rain Drop mode	Ninth mode: 100% Full Backlit mode
	Fourth mode: Ripple mode	Tenth mode: Radar mode
	Fifth mode: Random Reactive mode	Eleventh mode: Backlit OFF
	Sixth mode: Reactive mode

● All above modes can be adjusted with the following key sequence:

◆ Fn + Alt + J : Decrease speed
◆ Fn + Alt + L : Increase speed

● Hold Fn + Alt + T for 3 seconds to turn off all backlit (including CM1 and CM2).
- Only the backlit modes with ⚙ can be adjusted using the following:

◆ Fn + Alt + Z : Adjust color red (R) brightness. 10 Levels.
◆ Fn + Alt + X : Adjust color green (G) brightness. 10 Levels.
◆ Fn + Alt + C : Adjust color blue (B) brightness. 10 Levels.
◆ Fn + Alt + V : Erase red, green and blue color setting.
◆ Fn + Alt + Spacebar (Color palette) : Activate color palette to display various colors on each key, press on the desired color, all the keys will automatically change to match.

RGB LED Zone Customization Modes

Fn + Alt + G	CM1 cycle:First step: Turn on user's customized zone and color.Second step: Turn on user's customized zone and color in breathe mode.Third step: Turn off CM1.
Fn + Alt + B	CM2 cycle:First step: Turn on user's customized zone and color.Second step: Turn on user's customized zone and color in breathe mode.Third step: Turn off CM2.
Fn + Alt + Caps Lock (REC)	Press for 3 seconds until the G (CM1) and B (CM2) keys light up,choose the layer for setting, press it again and start recording.
Caps Lock + Z	Adjust color red (R), 10 levels.
Caps Lock + X	Adjust color green (G), 10 levels.
Caps Lock + C	Adjust color blue (B), 10 levels.
Caps Lock + V	Erase all LED light
Caps Lock + Spacebar	Color palette
Caps Lock + Left Shift	REC over, finish recording

RGB LED Zone Customization Modes

Recording steps:

- Adjust to the color first, then set the individual keys to be set to that color.

1. Press Fn + Alt + Caps Lock for 3 seconds, the buttons G (CM1) and B (CM2) will illuminate then press G to set CM1 and press B to set CM2.
2. When starting recording mode, Caps Lock will display the current LED color. The color can be adjusted by hitting Caps Lock + Z / X / C / V. After setting the desired color, hitting any key on the keyboard will set that key to the selected color.
3. Repeating the above steps allows the user to set different colors to different keys. If the key has been set, press again to cancel the setting.
4. To finish recording, press Caps Lock + Left Shift (REC over) to finish recording. The color of the Caps Lock key is the value you set.

Note:

• When starting recording mode, Caps Lock will display the current LED Color.
• CM1、CM2 can work with other LED light modes at the same time. CM1 and CM2 can be turned on along with other lighting modes. In addition, CM1 has the priority over CM2 when the zone overlaps. Press Fn + Alt + T for 3 seconds to turn off ALL backlit modes.
• If there is no activity in 30 seconds in the recording mode, the recording session will terminate without saving.
• Caps Lock LED color follows the "100% Full Backlit mode".

Ducky Gaming Interaction Mode

Ducky Gamble mode

Fn + Alt + N	2 blocks flashing
Fn + Alt + M	4 blocks flashing

Operation method:

Hold the combine keys for 3 seconds to perform multi-block flashing. Press the spacebar and it will randomly stay on one block. Press the spacebar again to start the next round.

Note:

● Ducky Gamble mode can be adjusted using the following:

◆ Fn + Alt + J : Decrease speed.
◆ Fn + Alt + L : Increase speed.

- If you start any light mode on Fn + Alt layer, the Gamble mode will be closed.

- If there is no activity in 10 minutes, the gaming interaction mode will terminate.

Ducky Minesweeper mode

Fn + Alt + ,

Minesweeper game

RGB LED Operation method:

Press for 3 seconds to start the minesweeper game. The keyboard will randomly select 1 or several buttons as mines. When the user turns the button in turn, the color will be displayed. The green color will continue to play the game safely. The red button is used as the mine, the game will end. At the end of the game, it will stay in the original display light color; press the blank button to enter the next round.

Multimedia Function

Fn + W	Mouse cursor up	Fn + Q	Left mouse button
Fn + A	Mouse cursor left	Fn + E	Right mouse button
Fn + S	Mouse cursor down	Fn + R	Roller up
Fn + D	Mouse cursor right	Fn + F	Roller down

Debounce Time Setting

5ms	Fn + Alt + Y	Hold the combine keys for 3 sec, the keyboard will flash 3 times to indicate the debounce time has been switched successfully.
10ms (Default)	Fn + Alt + U
15ms	Fn + Alt + I
25ms	Fn + Alt + O

Note:

The method is to adjust the debounce time of the metal shrapnel in the mechanical shaft during the pressing process. The shorter the time, the sooner it can be triggered, but if the time is too short may cause misjudgement. If it's not necessary to change the time, the default value is recommended.

Demo Mode

Hold Left Ctrl + Left Shift + Caps Lock then plug the keyboard into power source

Note: It is suitable for plugging in the mobile power supply or USB charging stand to provide lighting effects display, and the keyboard won't send any signal. Please note that it is limited to power supply devices with an output voltage of 5V. If the voltage does not match, the keyboard may be damaged.

Display Mode

Hold Fn + Alt + Ctrl for 3 sec

To display various LED backlit modes

Note: Used for showcasing purposes.

Reset To Factory Defaults

US ANSI and EU ISO layout	Left Windows key + Right Windows key
JP JIS layout	Fn+ Left Windows key

Note:

Hold for 3 seconds. The keyboard's backlight will flash 3 times to indicate the keyboard has been reset.

Enable / Disable Windows Function (Windows Key Lock)

Fn + any Alt key + any Windows key for 3 seconds, the keyboard's backlit will flash 3 times to indicate the keyboard has been enabled / disabled.

DIP Switch Functions

key switch Function

1. Applicable keys: Fn/Alt/Ctrl/Windows/Caps lock

2. Operation:

● Press Fn + Alt + k for 5 seconds.
● Until the ESC, L_Ctrl, L_Win, L_Alt, R_Alt, R_Win, Fn, R_Ctrl, and Caps lock keys are all lighting up. The colorways are respectively pink, red, orange, yellow, green, blue, indigo and purple.

● Except for Caps lock key, the rest of 6 keys are able to switch each function and color at will. (2 keys max at the same time)

- Press Caps lock once will change its own function to Fn (turns into indigo LED color) then L_Ctrl key (turns into red LED color) in order.

- Press Esc key once to finish the switching function. Note: You can press Esc key to leave the switching function before starting it.

DIP switch fuctions

DIP1	OFF (Default)	ON
	Windows key ON	Windows key OFF
DIP2	OFF (Default)	ON
	N-Key Rollover mode	6-Key Rollover mode
DIP3	OFF (Default)	ON
	Ducky Vender ID (VID)	Vender ID definable
DIP4	OFF (Default)	ON
	Standard mode	Display mode

Note : You can input the ideal VID in both situation, but the VID can be only changed when DIP 3 turned on.

Ducky Mecha/ One 2 Mini

Step 1. Profile selections

Fn + Alt +	1	=	Switch to profile 1	Factory settings (Default)
	2		Switch to profile 2	Customize Macro key features
	3		Switch to profile 3
	4		Switch to profile 4
	5		Switch to profile 5
	6		Switch to profile 6

Note:

• When keyboard is plugged in, Caps Lock and Number Keys will blink based on selected profile number.
• Adjust profile to 2\~6 in order to set Macro.
  ● After profile is switched, Caps Lock or Indicator light will blink based on the current profile number.

Step2. To start Macro recording

Press Fn + Alt + Tab for 3 seconds to start Macro recording. Once in recording mode the Caps Lock or indicator lights will flash slowly.

Step3. Press a key to start recording Macro

Press on the key you want to use to activate Macro. The key pressed will blink (Non-backlit version will not) and the Caps Lock or indicator lights will flash swiftly.

Step4. Recording Macro

Enter any key, and choose the Macro implementation and record time option.

Step5. To continue recording another key (Jump out the current recording file)

Press Fn + Alt to choose another key to continue recording.

Step6. Finish recording

Press Fn + Alt + Tab for 1 second to finish recording and back to the profile.

Ducky Mecha/ One 2 Mini

Hotkeys Function

Fn + Alt +	Tab	Start recording : Press for 3 seconds. Finish recording: Press for 1 second.
	ESC	Caps Lock will blink in the amount of selected profile number.
	Backspace	Delete current profile value.

Fn + Alt

Press for 1 sec to finish recording the current key and choose another key to record.

Ducky Mecha/ One 2 Mini

Setting Section

Ducky Mini Macro configurable keyboard layer

• Standard layer
  Fn layer
  ● Fn + Ctrl layer

Ducky Mini Macro unsettable key

Fn
Caps Lock

Note:

● Support N keys recorded at the same time, and N keys recorded at the same time when outputting.
- Macro function will be based on the user's typing speed and record it.

Ducky Mecha/ One 2 Mini

Multimedia Function Keys

Fn + Windows key + Keys below
A	Mute	G	Previous playlist	M	Search	S	Mouse cursor up
B	Volume up	H	Calculator	N	Previous page	T	Mouse cursor down
C	Volume down	I	My computer	O	Next page	U	Mouse cursor left
D	Play / Pause	J	Browser	P	Mouse left click	V	Mouse cursor right
E	Stop	K	Mail	Q	Mouse right click	W	Mouse scroll up
F	Next playlist	L	Multimedia	R	Mouse middle click	X	e scroll down

Note: Need to be recorded first before use.

Ducky Mecha/ One 2 Mini

Keyboard Button Function Keys

Fn + Shift+ Keys below
A		Prompt profile value	N		Backlit mode : Wave mode (Default)
B		Profile 1	O		Backlit mode : Color Cycle mode
C		Profile 2	P		Backlit mode : Rain Drop mode
D		Profile 3	Q		Backlit mode : Ripple mode
E		Profile 4	R		Backlit mode : Random Reactive mode
F		Profile 5	S		Backlit mode : Reactive mode
G		Profile 6	T		Backlit mode : 100% Full backlit mode
H		Backlit modes switching	U		Backlit mode : Breathe mode
I		Adjust color red	V		Backlit mode : Radar mode
J		Adjust color green	W		Backlit mode : Backlit OFF
K		Adjust color blue	X		The key “ . ” on number pad (Num_)
L		Erase all value	Y		Number Lock
M		Color palette

Note: 1. Need to be recorded first before use. 2. All versions support functions without an icon

Ducky Mecha/ One 2 Mini

Windows Common Function Keys

Ctrl + C	Copy select item	Windows + D	Desktop
Ctrl + X	Cut select item	Windows + M	Minimize all windows
Ctrl + V	Paste select item	Windows + L	Lock computer or change user
Ctrl + Z	Undo	Windows + R	Open [Run] window
Ctrl + Y	Redo	Windows + F	Search files or folders
Ctrl + N	Open new file	Windows + ↑	Maximize all windows
Ctrl + O	Open current file	Windows+ ↓	Minimize windows
Ctrl + S	Save file change	Windows + ←	Maximize window to the left side
Ctrl + P	Print file	Windows + →	Maximize window to the right side
Alt + F4	Quit the software	Windows + Home	Minimize all windows other than the one used

• http://windows.microsoft.com/en-us/windows/keyboard-shortcuts

Ducky Mecha/ One 2 Mini

Set Up Example

Note: Set the profile to profile 2\~6 before setting Macro.

Example A Configure the key "Z" to "Q" output.

Operation method :

Press Fn + Alt + Tab for 3 seconds → Press Z → Press down Q → Press Fn + Alt → Press Fn + Alt + Tab for 1 second

Example B To set Z as show "desktop" (under Windows system)

Operation method :

Press Fn + Alt + Tab for 3 seconds → Press Z → Press Windows key + D → Press Fn + Alt → Press Fn + Alt + Tab for 1 second

Example C - To set Fn + Ctrl + M as "mute volume"

Operation method :

Press Fn + Alt + Tab for 3 seconds → Press Fn + Ctrl + M → Press Fn + Windows key + A → Press Fn + Alt →

Press Fn + Alt + Tab for 1 second

Example D To set Fn + Ctrl + Q as "Reactive mode"

Operation method :

Press Fn + Alt + Tab for 3 seconds → Press Fn + Ctrl + Q → Press Fn + Shift + S → Press Fn + Alt → Press Fn + Alt + Tab for 1 second

Ducky Channel

www.duckychannel.com.tw