ID-880H - Radio ICOM - Free user manual and instructions
Find the device manual for free ID-880H ICOM in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Amateur Radio Transceiver |
| Brand | ICOM |
| Model | ID-880H |
| Frequency Bands | 144 MHz (2m) and 430 MHz (70cm) |
| Output Power | 50W (High), 15W (Medium), 5W (Low) |
| Operating Modes | Analog FM, D-STAR (Digital Voice and Data) |
| Power Supply | 13.8V DC |
| Dimensions (W x H x D) | 140 x 40 x 185 mm (5.5 x 1.6 x 7.3 in) |
| Weight | Approximately 1.2 kg (2.65 lb) |
| Memory Channels | 200 channels |
| Display | Full dot-matrix LCD with multi-color backlight |
| GPS Receiver | Built-in for D-STAR position reporting |
| Connectivity | USB port for programming and firmware updates |
| Audio Output | Built-in speaker, external speaker jack (3.5 mm) |
| Microphone | Supplied HM-133 with up/down keys |
| Maintenance and Cleaning | Clean with soft dry cloth; avoid solvents |
| Safety | Use only specified power supply; avoid excessive heat |
| Spare Parts and Repairability | Contact authorized ICOM service center |
| General Information | Designed for amateur radio use; supports D-STAR |
Frequently Asked Questions - ID-880H ICOM
How do I program memory channels on the ID-880H?
To program a memory channel, first select the desired frequency and mode. Press V/M to enter memory mode, then press and hold MW (Memory Write) for 1 second. Use the tuning dial to select an empty channel, then press MW again to store.
What is the maximum power output of the ID-880H?
The ID-880H can output up to 50 watts on both VHF (144 MHz) and UHF (430 MHz) bands. It also has medium (15W) and low (5W) power settings.
Does the ID-880H support D-STAR digital mode?
Yes, the ID-880H fully supports D-STAR (Digital Smart Technologies for Amateur Radio) for both digital voice and data communication, including GPS position reporting.
How do I set the clock on the ID-880H?
Press SET to enter the set mode, then rotate the dial to select 'Clock Set'. Press SET again, then use the dial to adjust the time. Press SET to confirm.
Can I use the ID-880H as a base station?
Yes, it can be used as a base station with an appropriate 13.8V DC power supply. Connect an external antenna (e.g., a quarter-wave ground plane) and optionally an external speaker or microphone.
How do I reset the ID-880H to factory defaults?
Turn off the radio. While holding down the MW and V/M keys, turn on the power. The display will show 'Reset All'. Press SET to confirm. This clears all memories and settings.
What type of antenna connector does the ID-880H use?
The ID-880H uses a SO-239 (UHF female) connector for the antenna. It works with PL-259 plugs commonly used in amateur radio.
How can I update the firmware on the ID-880H?
Firmware updates are performed via the USB port on the front panel. Download the latest firmware from ICOM's website, copy it to a USB flash drive, insert it into the radio, and follow the update procedure in the manual.
Can the ID-880H monitor airband frequencies?
No, the ID-880H is designed for amateur radio bands only (144-148 MHz and 430-450 MHz). It does not receive airband (118-137 MHz) without modification, which is not recommended.
How do I connect an external speaker to the ID-880H?
Connect an external speaker with an 3.5 mm mono plug to the 'SP' jack on the rear panel. The built-in speaker is automatically disabled when a plug is inserted.
User questions about ID-880H ICOM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Radio in PDF format for free! Find your manual ID-880H - ICOM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ID-880H by ICOM.
USER MANUAL ID-880H ICOM
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ICOM
Model : ID-880H
Category : Radio