SFC 14-A - Drill HILTI - Free user manual and instructions
Find the device manual for free SFC 14-A HILTI in PDF.
| Product Type | Cordless Drill/Driver |
| Brand | Hilti |
| Model | SFC 14-A |
| Battery Voltage | 14.4 V |
| Battery Type | Li-Ion |
| Chuck Type | Keyless |
| Chuck Capacity | 1/32 in. to 1/2 in. (1 mm to 13 mm) |
| No-Load Speed | 0-600 RPM (variable) |
| Max Torque | 30 Nm |
| Drilling Capacity (Steel) | 1/2 in. (13 mm) |
| Drilling Capacity (Wood) | 1-1/4 in. (32 mm) |
| Weight (with battery) | 2.1 lbs (0.95 kg) |
| Dimensions (LxH) | 8.5 in. x 7.5 in. (216 mm x 190 mm) |
| Power Source | Battery (14.4V Li-Ion) |
| Main Functions | Drilling, screwdriving, hammer drilling (if applicable) |
| Maintenance | Clean with dry cloth; check battery contacts; lubricate chuck if needed |
| Cleaning | Wipe with dry cloth; do not use water or solvents |
| Safety Features | Safety trigger lock; overload protection; electronic clutch (if applicable) |
| Spare Parts | Battery pack, charger, chuck, carbon brushes (if brushed motor) |
| Repairability | Serviceable by Hilti centers; DIY replacement of brushes, chuck |
| General Information | Compact design; ideal for light to medium duty tasks; LED light (if applicable) |
Frequently Asked Questions - SFC 14-A HILTI
User questions about SFC 14-A HILTI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Drill in PDF format for free! Find your manual SFC 14-A - HILTI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SFC 14-A by HILTI.
USER MANUAL SFC 14-A HILTI
natural_image
Top-down view of a mechanical component with a central slot and two circular holes (no text or symbols visible)
natural_image
Close-up of a mechanical component with a labeled slot (no text or symbols beyond the number 2)SFC 22-A/SFC 14-A cordless drill / driver
It is essential that the operating instruct are read before the power tool is open the first time.
Always keep these operating instructions get her with the power tool.
Ensure that the operating instructions with the power tool when it is given persons.
Contents Page
| 1 General information 1 |
| 2 Safety instructions 2 |
| 3 Description 4 |
| 4 Technical data 5 |
| 5 Before use 6 |
| 6 Operation 7 |
| 7 Care and maintenance |
| 8 Troubleshooting |
| 9 Disposal |
| 10 Manufacturer's warranty - tools |
| 11 EC declaration of conformity (original) |
1 These numbers refer to the illustrations. You can find the illustrations at the beginning of the operating instructions.
In these operating instructions, the designation "power tool" always refers to the SFC 22-A or SFC 14-A cordless drill / driver with battery fitted.
Product overview 1
to other
(1) Keyless chuck
② Torque and drilling mode setting ring
③ 2-speed gear selector switch
④ Forward / reverse selector switch with transport lock
⑤ Control switch (with electronic speed control)
⑥ Grip
⑦ Lamp
⑧ Belt hook (optional)
⑨ Release buttons with additional function (charge status display activation)
⑩ Charge status and fault display (Li-ion battery) 9
9
10
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situat could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situat could lead to slight personal injury or damage to the equipment or other property.
NOTE
Draws attention to an instruction or other useful tion.
1.2 Explanation of the pictograms and other information
Warning signs
General warning
n that Obligation signs
informa-
Read the operating instructions before use.
Symbols
Direct current
Rated speed under no load
Revolutions per minute
Drilling without hammering
Location of identification data on the power The type designation can be found on the typ ation plate at the base of the power tool and
number on the side of the casing. Make a data in your operating instructions and always refer to when making an enquiry to your Hilti representative service department.
Type:
Generation: 01
tool
identificio.:
the serial
2 Safety instructions
NOTE
The safety rules in section 2.1 contain all gene rules for power tools which, in accordance with applicable standards, must be listed in the open instructions. Accordingly, some of the rules listed not be relevant to this tool.
2.1 General power tool safety warnings
a)
WARNING
Read all safety warnings and all instruction to follow the warnings and instructions in electric shock, fire and/or serious injury. warnings and instructions for future referer The term "power tool" in the warnings refer your mains-operated (corded) power tool or operated (cordless) power tool.
2.1.1 Workareasafety
a) Keep work area clean and well lit. Clutter areas invite accidents.
b) Do not operate power tools in explosive spheres, such as in the presence of flam liquids, gases or dust. Power tools create which may ignite the dust or fumes.
c) Keep children and bystanders away while ing a power tool. Distractions can cause y control.
2.1.2 Electrical safety
a) Power tool plugs must match the outlet. modify the plug in any way. Do not use apter plugs with earthed (grounded) power. Unmodified plugs and matching outlets will risk of electric shock.
b) Avoid body contact with earthed or ground surfaces, such as pipes, radiators, ranges refrigerators. There is an increased risk of shock if your body is earthed or grounded.
c) Do not expose power tools to rain or water tions. Water entering a power tool will increase risk of electric shock.
d) Do not abuse the cord. Never use the carrying, pulling or unplugging the power Keep cord away from heat, oil, sharp ed
moving parts. Damaged or entangled cords increase safety risk of electric shock.
When operating a power tool outdoors, use an rating extension cord suitable for outdoor use. Use of may cord suitable for outdoor use reduces the risk electric shock.
f) If operating a power tool in a damp location unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
ns. Fail- 2.1.3 Personal safety may result
Save Stay alert, watch what you are doing and use ice. common sense when operating a power tool. It is to not use a power tool while you are tired or the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust red or dark mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce atmo- personal injuries.
c) Prevent unintentional starting. Ensure the switch sparks is in the off-position before connecting to power source and/or battery pack, picking up or carrying operational tool. Carrying power tools with your finger or lose switch or energising power tools that have the s on invites accidents.
d) Remove any adjusting key or wrench before tu ing the power tool on. A wrench or a key left tached to a rotating part of the power tool may any in personal injury.
Tools Do not overreach. Keep proper footing and balance at all times. This enables better control of power tool in unexpected situations.
Dress properly. Do not wear loose clothing or and jewellery. Keep your hair, clothing and gloves electric away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
get cond- g) if devices are provided for the connection of ( ase the extraction and collection facilities, ensure these are connected and properly used. Use of dust cord for collection can reduce dust-related hazards.
2.1.4 Power tool use and care
a) Do not force the power tool. Use the c-power tool for your application. The correct tool will do the job better and safer at the which it was designed.
b) Do not use the power tool if the switch turn it on and off. Any power tool that controlled with the switch is dangerous and repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach dren and do not allow persons unfamiliar power tool or these instructions to operat power tool. Power tools are dangerous in of untrained users.
e) Maintain power tools. Check for misalignm binding of moving parts, breakage of part any other condition that may affect the power tool's operation. If damaged, have the power repaired before use. Many accidents are ca poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool in accordance with these instructions, taking account the working conditions and the w be performed. Use of the power tool for operations different from those intended could res hazardous situation.
2.1.5 Battery tool use and care
a) Recharge only with the charger specified manufacturer. A charger that is suitable for one type of battery pack may create a risk of used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery pa create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like paper clips, keys, nails, screws or other small metal that can make a connection from one to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be e from the battery; avoid contact. If contact dentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ted from the battery may cause irritation or
2.1.6 Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the pow maintained.
2.2 Drill safety warnings
protect Wear ear protectors when impact drilling. Expos- t power to noise can cause hearing loss. e brate Use for auxiliary handle(s), if supplied with the tool Loss of control can cause personal injury. does hot-power tool by insulated gripping surfaces cannot when performing an operation where the en must accessory may contact hidden wiring. Cutting ac cessory contacting a "live" wire may make expose ce metal parts of the power tool "live" and could g tool the operator an electric shock.
2.3 Additional safety rules
2.3.1 Personal safety
of) modification of the machine or tampering with withparts is not permissible.
e b) the Hold power tool by insulated gripping surfaces, the hhen performing an operation where the fastener may contact hidden wiring. Fasteners contacting ent or "live" wire may make exposed metal parts of s and power tool "live" and could give the operator an electric shock.
ver) Always hold the power tool securely with both used hands on the grips provided. Keep the grips clean and free from oil and grease.
d) Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers during breaks between working.
Bits Avoid touching rotating parts. Switch the power g into tool on only after bringing it into position at work workpiece. Touching rotating parts, especially rotat- ing insert tools, may lead to injury.
ultf) inActivate the safety lock (forward / reverse switch in the middle position) before storing or transporting the power tool.
g) The power tool is not intended for use by children, by the debilitated persons or those who have received no instruction or training.
The appliance is not intended for use by debil ated persons who have received no special tra ing. Keep the appliance out of reach of childr cks Dust from materials, such as paint containing lead, some wood species, concrete / masonry / stone con- taining silica, and minerals as well as metal, may harmful. Contact with or inhalation of the dust ma objects, reuse allergic reactions and/or respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning (chromate, wood preservative).
acc Material containing asbestos must only be treated by specialists. Where the use of a dust-extraction device is possible it shall be used. To achieve high level of dust collection, use a suitable dust extractor. When indicated wear a respirator appropriate for the type of dust generated. Ensure that the workplace is well ventilated. Follow national requirements for the materials you want work with.
j) The user and any other persons in the v must wear suitable eye protection, a hard ear protection, protective gloves and breath protection while the tool is in use.
2.3.2 Careful use of the power tool
a) Secure the workpiece. Use clamps or a secure the workpiece. The workpiece is the more securely than by hand and both hand free to operate the power tool.
b) Check that the insert tools used are con with the chuck system and that they are in the chuck correctly.
c) Large and heavy insert tools must only be erated in first gear. There is otherwise a the tool will be damaged when it is switch under unfavorable conditions, the chuck might detached.
2.3.3 Careful use of the cordless tool
a) Ensure the switch is in the off position inserting battery pack. Inserting the battery into power tools that have the switch on accidents.
b) Do not expose batteries to high temperat keep them away from fire. This presents explosion.
c) Do not disassemble, squash or incinerate ies and do not subject them to temperat
icinity80°C. This presents a risk of fire, explosion or i hat, through contact with caustic substances.
Avoid ingress of moisture. Ingress of moisture may cause a short circuit, resulting in burning injuries fire.
e) Observe the special guidelines applicable to the vice transport, storage and use of Li-ion batteries.
(ust) Avoid short circuiting the battery terminals. Before inserting the battery in the tool, make such that the battery terminals and the terminals in compatible oil are free from foreign objects. Short circuitir sectured battery terminals presents a risk of fire, expl and chemical burns.
(eg) op Do not charge or continue to use damaged bars, risk terres (e.g. batteries with cracks, broken parts, and dentr, or pushed-in and/or pulled-out contacts).
t h be If the battery is too hot to touch it may be de Place the tool in a location where it can be under observation, well away from flammable ma terials, and allow it to cool down. Contact Hill Service after the battery has cooled down. before
pack 2.3.4 Electrical safety nvites
Before beginning work, check the working area (e.g. using and metal detector) to ensure that no conceal a electric of cables or gas and water pipes are present. External metal parts of the power tool may become better-for example, when an electric cable is damaged accidentally. This presents a serious riskof electricshock.
3 Description
3.1 Use of the product as directed
The SFC 22-A or SFC 14-A is a hand-held, battery powered combination drill for screwing and unscrewing screws and for drilling in steel, wood and plastic.
Do not use the battery as a power source for other unspecified appliances.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
The power tool is designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any special hazards that may be encountered. The power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
3.2 Standard equipment includes:
1 Power tool
1 Operating instructions
NOTE
Approved accessories are available from your Hilti Center or can be ordered online at www.hilti.com.
3.3 Additional items required for operating the tool:
A suitable battery of the specified type (see table in the Technical Data section) and a suitable battery charger from the C 4/36 series.
3.4 Charge state and overheating indicator display on the Li-ion battery
When the lithium-ion battery is in use, the charge status can be indicated by gently pressing one of the battery release buttons (press until resistance is felt - do not release the battery). The display on the rear of the battery provides the following information:
| LEDs light constantly LEDs blnk | Charge status C | |
| LED 1,2,3,4 | - | C ≧ 75 % |
| LED 1,2,3 | - | 50 % ≧ C < 75 % |
| LED 1,2 | - | 25 % ≧ C < 50 % |
| LED 1 | - | 10 % ≧ C < 25 % |
| - | LED 1 | C < 10 % |
| - | LED 1 The battery has overheated | |
NOTE
Indication of the charge status is not possible while the power tool is in operation or immediately after operation. If the battery charge status LEDs flash, please refer to the information given in the Troubleshooting section.
3.5 Overload and overheating protection
The power tool is equipped with an electronic protection system to prevent overloading and overheating. The power tool switches itself off automatically in the event of overloading and overheating. After releasing the control switch, the power tool may not restart immediately when the switch is pressed again (while the power tool is cooling down).
4 Technical data
Right of technical changes reserved.
| Power tool | SFC 14-A SFC 22-A | |
| Rated voltage (DC voltage) 14.4 V 21.6 V | ||
| Weight in accordance with EPTA 1.5 kg 1.7 kg procedure 01/2003 | ||
| Speed in 1st gear (with B 14/0.3500/min 0...600/min B 22/2.6(01)) | ||
| Speed in 2nd gear (with B 14/0.31,700/min 0...1,800/min B 22/2.6(01)) | ||
| Torque with tool set to drilling bol (soft/flexible joint) | Maxm- 24 Nm | Max. 28 Nm |
| Torque range (15 settings) | 1.5...10 Nm | 1.5...10 Nm |
Drilling diameter range
| Keyless chuck clamping range,ø 1.5...13 mm | |
| Drilling diameter range in wood (soft),ø | 1.5...20 mm |
| Drilling diameter range in wood (hard),ø | 1.5...12 mm |
| Drilling dia. range in metal,ø | 1.5...10 mm |
NOTE
The sound pressure and vibration values given in these instructions have been measured in accordance with a standardized test and may be used to compare one electric tool with another. They may be used for a preliminary assessment of exposure. The data given represents the main applications of the electric tool. However, if the electric tool is used for different applications, with different accessories or is poorly maintained, the data may vary. This may significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This may significantly reduce exposure over the total working period. Prescribe additional safety measures to protect the operator from the effects of noise and/or vibration, such as: maintaining the tool and accessories, keeping the hands warm, reorganization of work patterns.
Noise information in accordance with EN 60745:
| Sound power level for the SWAFC 22 - A, L | 80 dB (A) |
| Sound power level for the SWAFC 14 - A, L | 80 dB (A) |
| Uncertainty for the given sound power WA level, K 3 dB (A) | |
| Emission sound pressure level for the SFAC 22-69 LdB (A) | |
| Emission sound pressure level for the SFAC 14-69 LdB (A) | |
| Uncertainty for the given sound pressure pA level, 3k dB (A) | |
Total vibration (vector sum of three directions), determined in accordance with EN 60745:
| For the SFC ah | 22-A: Screwdriving without impact actions,2 | |
| For the SFC ah | 14-A: Screwdriving without impact actions,2 | |
| Uncertainty for screwdriving without impact action, K 1.5 m/s2 | ||
| For the SFC | 22-A: Drilling in h,D metal, a | 2 m / s2 |
| For the SFC | 14-A: Drilling in h,D metal, a | 2 m / s2 |
| Uncertainty for drilling in metal, K 1.5 m/s2 | ||
| Battery B 14/1.6 Li-Ion B 14/3.3 Li-Ion | |
| Rated voltage 14.4 V 14.4 V | |
| Capacity 1.6 Ah 3.3 Ah | |
| Energy content 23.04 Wh 47.52 Wh | |
| Weight 0.36 kg 0.60 kg | |
| No. of cells | 4 |
| Battery | B 22/1.6 Li-Ion | B 22/2.6 Li-Ion (01) | B 22/2.6 Li-Ion (02) | B 22/3.3 Li-Ion | B 22/5.2 Li-Ion |
| Rated voltage | 21.6 V | 21.6 V | 21.6 V | 21.6 V | 21.6 V |
| Capacity | 1.6 Ah | 2.6 Ah | 2.6 Ah | 3.3 Ah | 5.2 Ah |
| Energy content | 34.56 Wh | 56.16 Wh | 56.16 Wh | 71.28 Wh | 112.32 Wh |
| Weight | 0.48 kg | 0.78 kg | 0.48 kg | 0.78 kg | 0.78 kg |
| No. of cells | 6 | 12 | 6 | 12 | 12 |
5 Before use
5.1 Charging a previously used battery
Make sure that the outer surfaces of the battery are clean and dry before inserting the battery in the corr charger.
Read the operating instructions for the charger for further information about the charging procedure.
5.2 Inserting the battery 2
CAUTION
Before fitting the battery, check that the power tool is switched off and that the safety lock is engaged (forward/reverse switch in the middle position). Use only the Hilti batteries approved for use with this power tool.
Check that the battery is securely seated in the tool
CAUTION
A falling battery may present a risk of injury to yourself and others.
5.3 Removing the battery 3
5.4 Transport and storage of batteries
CAUTION
Fire hazard. Never transport batteries in loose, bulk form.
There is a risk of short circuiting.
Pull the battery out of the locked position (wo tion) and move it into the first latching positio position).
Observe national and international transport regula when shipping batteries (transportation by road, or air).
5 pBelt hook 4
CAUTION
Check that the belt hook is fitted securely before tions beginning work. rail, sea
The belt hook allows the power tool to be a belt worn by the operator. The belt hook can to the other side of the power tool for use persons.
en
- Remove the battery from the power tool.
- Fit the mounting plate into the guides provided.
- Secure the belt hook with the two screws.
6Operation
CAUTION
The tool may get hot during use. Wear protective
CAUTION
When drilling and screwdriving, the grip of t may be deflected laterally (the tool tends to about its own axis).
CAUTION
To avoid injuries caused by the insert tool, protective gloves when changing insert tools.
DANGER
Set the forward / reverse switch to the mic or remove the battery from the power tool.
6.1 Setting forward or reverse rotation 5
NOTE
The forward / reverse switch is used to select of rotation of the drive spindle. An interlock p switching while the motor is running. The control is locked when the forward / reverse switch is middle position. Push the forward / reverse swing the right (power tool held in working direction) forward rotation. Push the forward / reverse swing the left (power tool held in working direction) reverse rotation.
6.2 Speed selection using the 2-speed gear selector switch 6
WARNING
Large and heavy insert tools must only be in first gear. There is otherwise a risk that is damaged when it is switched off or, under un conditions, the chuck might be detached.
NOTE
The mechanical 2-speed gear selector switch can be used to set the speed range required. Speed charged battery. SFC 14-A: 1st gear: 0-500 /min gear: 0-1700 /min. SFC 22-A: 1st gear: 0-600 /min., 2nd gear: 0-1800 /min.
6.3 Switching on / off
Speed of rotation can be controlled smoothly up to imum speed by pressing the control switch slowly.
he tool
6.4 Fitting the drill bit
- Check that the connection end of the drill bit is clean. Clean the connection end if necessary.
- Insert the drill bit in the keyless chuck and ther wear turn the chuck firmly by hand until several click heard.
- Check that the drill bit is held securely.
Idle position 6.5 Removing the drill bit
- Open the keyless chuck.
- Pull the insert tool out of the chuck.
6.6 Drilling the direction
CAUTION revents
Use switches or a vice to secure the workpiece. The workpiece is thus held more securely than by hard and both hands remain free to operate the power to select Turn the torque and operating mode setting ring to select the drilling symbol.
- Move the forward / reverse switch to the "Forward position.
6.7 Screwdriving
6.7.1 Fitting the bit holder / bit
operated the keyless chuck.
The tool will be bit adapter in the keyless chuck and it favorable on the chuck firmly by hand until tight.
- Check that the bit adapter is held securely (check by pulling).
- Fit the bit in the bit holder. be
with 6.7.2 fully screwdriving
n.1. 2nd Select the torque function on the setting ring for torque and drilling.
- Set the forward / reverse switch to the desired direction of rotation.
ired.3 Removing the bit / bit holder
- Remove the bit from the bit holder.
- Open the keyless chuck.
- Remove the bit adapter.
en
7 Care and maintenance
WARNING
Repairs to the electrical section of the power to be carried out only by trained electrical spec
running water for cleaning. This may negatively affect electrical safety of the power tool. alists.
7.1 Care of the power tool
CAUTION
Keep the power tool, especially its grip surface clean and free from oil and grease. Do not ing agents which contain silicone.
Never operate the power tool when the ventilati are blocked. Clean the ventilation slots carefully a dry brush. Do not permit foreign objects to interior of the power tool. Clean the outside of tool at regular intervals with a slightly damp cl not use a spray, steam pressure cleaning equip
7.2 Care of the Li-ion battery
NOTE
Battery performance drops at low temperatures.
NQTEclean-
Store the battery in a cool and dry place.
on slotter to achieve maximum battery life, stop using battery as soon as a significant drop in battery per enter the noticed.
NOTE power
both. If Do use continues, further battery discharge will be stopped automatically before the battery cells suffer damage.
- Charge the batteries using the specified and approv Hilti battery chargers for Li-ion batteries.
8 Troubleshooting
Fault Possible cause Remedy
| The power tool doesn't run. | The battery is discharged or this battery must be heard to engage pushed all the way in. | with a double click or, respectively, needs to be charged. |
| Electrical fault. | Remove the battery from the tool and contact Hilti Service. | |
| The power tool doesn't run 1 LED blinks. | Time battery is discharged. | Change the battery and charge the empty battery. |
| The battery is too hot or too cold. | Bring the battery to the recommended working temperature. | |
| The on / off switch can't be pressed, i.e. the switch is locked. | The forward / reverse switch is middle position (transport lock en-the left or right. gaged). | Push the forward / reverse switch to the left or right. |
| The battery runs down more quickly than usual. | Very low ambient temperature. | Allow the battery to warm up slow to room temperature. |
| The battery doesn't engage an audible double click. | With retaining lugs on the battery dirty. | Clean the retaining lugs and push the battery in until it engages. Contact Hilti Service if the problem persists. |
| LED 1 blinks. | The battery is discharged. | Charge the battery. |
| The tool is overloaded (application limits exceeded). | Use the right power tool for the job (don't use a low-powered tool for heavy work). |
9 Disposal
CAUTION
Improper disposal of the equipment may have serious consequences: the burning of plastic components generates toxic fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or environmental pollution. Careless disposal may permit unauthorized and improper use of the equipment. This may result in serious personal injury, injury to third parties and pollution of the environment.
CAUTION
Dispose of defective batteries right away. Keep them out of reach of children. Do not disassemble or incinerate the batteries.
CAUTION
Batteries that have reached the end of their life must be disposed of in accordance with national regulations or returned to Hilti.
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
For EC countries only
Disposal of electric tools together with household waste is not permissible.
In observance of the European Directive on waste electrical and electronic equipment and its implementation in accordance with national law, electrical appliances that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
10 Manufacturer's warranty - tools
Please contact your local Hilti representative if you have questions about the warranty conditions.
11 EC declaration of conformity (original)
| Designation: Cordless drill / driver |
| Type: SFC 22-A/SFC 14-A |
| Generation: 01 |
| Year of design: 2010 |
We declare, on our sole responsibility, that this complies with the following directives and standa 2006/42/EC, until 19th April 2016: 2004/108/EC, as of 20th April 2016: 2014/30/EU, 2006/66/EC, 2011/65/EU, EN 60745-1, EN 60745-2-1, EN 60 EN ISO 12100.
Hilti Corporation, Feldkircherstrasse 100, FL-9494 Schaan
Paolo Luccini Tassilo Deinzer
Head of BA Quality and Process Management Business Area Electric Tools & Ac- 45-2015 03/2015
Executive Vice President
Business Unit Power Tools & Accessories 03/2015
Technical documentation filed at:
- SFC 22-A/SFC 14-A cordless drill / driver
- Product overview 1
- to other
- General information
- Safety notices and their meaning
- DANGER
- WARNING
- CAUTION
- NOTE
- Explanation of the pictograms and other information
- Symbols
- Safety instructions
- General power tool safety warnings
- Workareasafety
- Electrical safety
- Power tool use and care
- Battery tool use and care
- Service
- Drill safety warnings
- Additional safety rules
- Personal safety
- Careful use of the power tool
- Careful use of the cordless tool
- Description
- Use of the product as directed
- Standard equipment includes:
- Additional items required for operating the tool:
- Charge state and overheating indicator display on the Li-ion battery
- Overload and overheating protection
- Technical data
- Before use
- Charging a previously used battery
- Inserting the battery 2
- Removing the battery 3
- Transport and storage of batteries
- 6Operation
- Switching on / off
- he tool
- Screwdriving
- ired.3 Removing the bit / bit holder
- en
- Care and maintenance
- Care of the power tool
- Care of the Li-ion battery
- NQTEclean-
- NOTE power
- Troubleshooting
- Disposal
- Manufacturer's warranty - tools
- EC declaration of conformity (original)
Brand : HILTI
Model : SFC 14-A
Category : Drill