LZH-087 - Water pump Sunnydaze Decor - Free user manual and instructions

Product Type	Submersible Water Pump
Model	LZH-087
Brand	Sunnydaze Decor
Dimensions (L x W x H)	3.5 x 2.5 x 4 inches
Weight	1 lb
Power Supply	120V AC, 60Hz
Power Consumption	15 W
Flow Rate	200 GPH (gallons per hour)
Maximum Lift	6 ft
Maximum Submersion Depth	5 ft
Cord Length	6 ft
Outlet Diameter	1/2 inch
Material	Engineered Plastic
Noise Level	Low noise, suitable for indoor use
Operating Environment	Fresh water only, temperature up to 95°F
Primary Use	Fountains, small ponds, water features
Maintenance	Clean intake filter regularly; rinse with clean water
Safety Features	Thermal overload protection; submersible design
Included Accessories	2 nozzles, 1 adapter, instruction manual
Warranty	1-year limited manufacturer warranty

Frequently Asked Questions - LZH-087 Sunnydaze Decor

How do I start the pump for the first time?

Fully submerge the pump in water before plugging it in to ensure the impeller is primed. Then connect to a grounded outlet.

Can the pump run dry?

No, running the pump dry can damage the motor. Always keep it submerged. The pump has thermal overload protection but should not be run dry.

How do I clean the pump?

Unplug the pump and disassemble the front housing. Remove the impeller and clean it and the housing with a soft brush under running water. Do not use chemicals.

Why is my pump making noise?

Noise may be due to air trapped in the pump or debris in the impeller. Ensure it is fully submerged and clean the filter. If noise persists, check for wear.

What is the maximum flow rate?

The maximum flow rate is 200 gallons per hour at 0 ft lift. Flow decreases as lift height increases.

Can I use this pump with salt water?

No, this pump is designed for fresh water only. Salt water or chemicals will corrode the motor and void the warranty.

How do I adjust the water flow?

Use the included flow control adapter or adjust the nozzle size. Some models have a built-in flow control ring.

Is the pump suitable for outdoor use?

Yes, but it must be submerged or protected from direct rain. The electrical plug should be kept dry and sheltered.

What size tubing fits the outlet?

The outlet fits 1/2 inch ID tubing. Use the adapter if needed. Ensure a tight fit to prevent leaks.

How long is the power cord?

The power cord is 6 feet long. Use a GFCI outlet for safety, especially outdoors.

USER MANUAL LZH-087 Sunnydaze Decor

Thank you for choosing Sunnydaze Décor. If you have any questions, comments or concerns please feel free to contact us by phone at: 888-881-4668, by email: [e-mail], or you could also email us via our contact us page at: www.SerenityHealth.com/contact-us/.

We stand behind our brand and the quality of the items we sell. We will send new parts, or replace products at our discretion within the one year warranty period. Before we can help, you will need to provide proof of purchase with the date of purchase and photos of the defective merchandise. We will use the photos to determine the cause of defect and for future quality control.

61" 3-Tier Cornucopia Water Fountain(LZH-087)

Part Description Quantity Part Description Quantity
A Base Pedestal 1 F Medium	Basin 1
B Large basin 1 G Small pedestal 1
C Pump 1 H Small basin 1
D Board 1 | Fountain Topper 1
E Center Pedestal 1

SAFETY PRECAUTIONS

This fountain is intended for outdoor use only.

Place your fountain in a location where any water spills or splashing will not reach any other electrical equipment or cause damage.

Choose an appropriate location before installing the fountain. DO NOT lift or push/drag the water basin to relocate the fountain when it's filled with water. Empty the water basin before lifting.

Excessive weight or pressure on any of the fountain sections may cause it to tip or fall over.

Keep pets and children away from any of the fountain sections.

Some splashing may occur. To avoid injury from electrical shock, observe basic safety precautions and comply with the following instructions:

The pump on your fountain has no user serviceable parts. Only an authorized service representative should service the pump. Do not open the sealed pump housing as this may result in electrical shock. Refer to enclosed pump maintenance guide for cleaning.

1. Install the fountain pump correctly before operating it.

2. DO NOT allow the pump to run dry.

3. An adult should supervise children when they are around the pump.

4. Use the proper power source as indicated on the pump label.

5. Equip the electrical power for the pump with a ground fault circuit interrupter (GFCI).

6. If the entire fountain falls into the water accidentally, turn off the circuit breaker immediately.

7. If any leakage occurs around the pump housing, turn off the circuit breaker immediately and have the pump serviced by a registered technician.

8. Do not operate the fountain if the pump has been dropped or has a damaged power cord or plug.

9. If the plug or your wall receptacle gets wet due to water dripping down the power cord or for any other reason, do not remove the plug from the wall outlet until the circuit breaker is turned off

NOTE: Allow the pump power cord to hang at a lower level than the wall outlet to form a "drip loop

". This will help prevent water from dripping down the power cord and getting into the wall outlet.

1. Always unplug the fountain pump and any other independent electrical accessories

(e.g. lights) from the outlet when not in use and before cleaning or replacing parts.

1. Disconnect the power cord from the outlet by holding the plug, not by pulling on the power cord.

2. Periodically change the water. Clean the fountain water basin, the pump's outlet nozzle and the water tube for dirt and debris with a damp cloth if necessary.

3. Do not expose the pump to direct sunlight or to low temperatures for any period of time.

4. Keep the power cord away from high temperatures or heat sources.

5. Use only a UL-approved extension cord of the correct rating to avoid overheating

TROUBLESHOOTING

1. If your FOUNTAIN PUMP fails to operate please check the following:

a) Make sure the pump is plugged into the socket properly.

b) Check the water level in the fountain. Running the pump without sufficient water can damage the pump.

c) Check the setting of the flow control on the pump. Check the pump outlet nozzle and the water tube for dirt and deb Clean if necessary.

d) Make sure the pump is connected to the water tube tightly. Check the fountain tubing for kinks and obstructions

e) The pump may be "air locked". Plug and unplug the pump several times to clear any air that may have been trapped.

1. If the water does not flow out of the fountain, it may be caused by kinked or loose water tubes, make sure water tubes are connected properly.

ASSEMBLY PICTURES

Fig7 Fig 8 Fig 9

ASSEMBLY INSTRUCTIONS

Step 1: Place the base pedestal (A) and the large basin (B) on a level surface.(pls refer to fig .1)

Step 2: Route the pump (C)'s power cord downwards through the resin tube in large basin (B). Lay the pump (C) in the bottom of the large basin (B). And then route the pump (C)'s power cord through the base pedestal (A), the cord exits through the slot in the bottom of base pedestal (A).(pls refer to the fig. 2), Lastly align the large basin (B) with base pedestal (A), insert the large basin (B) and twist clockwise to lock in place securely.

Step 3: Align the center pedestal(E) with the large basin(B), make sure matching the slot under the center pedestal (E) to the blocks on the large basin as shown in Fig 3, insert the center pedestal(E) and twist clockwise to lock in place securely.

Step 4: Route the water tube of the fountain topper (1) downwards through the middle hole of the small basin (H), then align the fountain topper (1) with the small basin (H). Make sure matching the slot under the fountain topper (1) to the blocks on small basin (H) as shown in Fig4. Insert the fountain topper (1) and twist clockwise to lock in place securely

Step 5: Route the water tube of the assembled topper (I and H) downwards through the small pedestal (G). Align the assembled topper (I and H) with small pedestal (G), insert the assembled topper and twist clockwise to lock in place securely. pls refer to fig 5.

Step 6: Route the water tube of the assembled topper (H,I and G) downwards through the Medium Basin (F). Align the assembled topper (H,I and G) with Medium Basin(F), insert the assembled topper and twist clockwise to lock in place securely. pls refer to fig 6.

Step 7: Route the water tube of the assembled topper(I,H,G and F) downwards through the assembled Center Pedestal(E). Align the assembled topper (I,H,G and F) with center pedestal(E), insert the assembled topper and twice clockwise to lock in place securely.(pls see fig.7)

Step 8: Through the door of Center Pedestal, Connect the water tube to the outlet nozzle of pump (C). Make sure the connection is tight. (refer to fig .8)

Step 9: Put the board (D) located at the door of the Center Pedestal(E).(see fig .9)

Step 10: Fill the large basin (B) and medium basin (F) with water. Make sure the pump (C) is completely submerged in water.

Step 11: Plug the pump power cord to the wall outlet to run the fountain.

Be careful not to spill water onto the plug of the pump. DO NOT allow the pump to run dry!

ris.