BTCCD528 - Charger JUNG - Free user manual and instructions

Product Type	Bluetooth Audio Receiver/Amplifier
Brand	JUNG
Model	BTCCD528
Rated Voltage	AC 230 V ~, 50/60 Hz
Power Consumption (Standby)	0.37 W
Power Consumption (Operation)	< 4.00 W
Bluetooth Profiles	A2DP, AVRCP
Number of Audio Sources	Up to 6
Speaker Output (per channel)	2.5 W at 4 Ω
Stereo/Mono Mode	Auto-detect
Line-Out (AUX)	Impedance 470 Ω, Output Level 1 V
Ambient Temperature	0 °C to +50 °C
Humidity	15% to 90% (non-condensing)
Degree of Protection	IP20
Connection Type	Screw terminals (1×1.5 mm² or 1×2.5 mm²)
Speaker Cable Length (max)	5 m
Front Material	Solid glass
User Interface	8 sensor buttons
Installation Type	Flush-mounted device box (DIN EN 49073)
Safety	For qualified electricians; dry rooms only

Frequently Asked Questions - BTCCD528 JUNG

How do I pair my smartphone with the JUNG BTCCD528?

The device automatically enters pairing mode when switched on. Enable Bluetooth on your smartphone and select 'JUNG BTC...' from the list. The connection is established automatically.

How many audio sources can be stored?

Up to 6 audio sources can be taught in. The device attempts to connect to them in the order they were paired.

How do I delete all paired devices?

Press and hold the pause button for more than 10 seconds. This deletes all previously taught-in audio sources.

Can I use speakers other than JUNG LSM?

Yes, but only if the technical data (impedance 4 Ω, power handling 2.5 W) is identical. It is recommended to use the JUNG LSM modules.

What is the Bluetooth range?

The typical Bluetooth range is up to 10 meters (33 feet) in open space. Walls and obstacles may reduce the range.

How do I switch the device on/off?

Tap the lower half of the cover (sensor area) to show the buttons, then press the power button to switch on/off. The device enters standby mode.

What does the extension unit input do?

The extension unit input (terminal 1) allows you to switch the Bluetooth Connect on/off via an external switch, e.g., together with the room light. It must be on the same phase.

How do I pause playback?

Press the pause button (center button) once to interrupt playback. Press again to resume.

What should I do if there is no sound?

Check that the device is switched on (LED lit), the audio source is connected and playing, volume is up, and speakers are properly connected. Ensure the source is within range.

Is the device suitable for outdoor installation?

No, the device is only intended for dry rooms with IP20 protection. It must not be exposed to moisture or dust.

USER MANUAL BTCCD528 JUNG

Bluetooth Connect BTC...

Operating instructions

Description of device

The JUNG Bluetooth Connect BTC... consists of an operating cover and a flush-mounted power supply. The audio source (e.g. smartphone or MP3 player) is connected and the device is operated via the operating cover. The device is operated and set up via 8 sensor buttons.

The connections for mains voltage, loudspeakers and audio output are available on the power supply unit. The Bluetooth Connect can be operated with one or two loudspeaker modules LSM...

The music signal is transmitted via Bluetooth, amplified internally and output to loudspeakers or an external amplifier. The tracks and volume can be changed via sensor buttons. Up to 6 audio sources can be taught in, from which one audio source can be connected actively with the Bluetooth Connect.

Safety instructions

Electrical equipment must only be installed and assembled by qualified electricians. Failure to comply with these instructions may result in damage to the device fire or other hazards. This product is only intended for use in dry rooms. These instructions are an integral part of the product and must remain with the end customer.

Operation

The lower half of the cover is used for operation. All operations are made via 8 sensor buttons. In standby mode the buttons are hidden and are displayed each time you touch the lower area.

Switching on / Switching off

The Bluetooth Connect is switched on and off here (standby)

Note: After switching on, the Bluetooth Connect connects automatically to the last audio source if it can be reached. If the source is not available, e.g. because it is not within range, the next audio source is connected. The Bluetooth Connect attempts to reach the taught-in audio sources in the sequence they were taught in.

While searching for the connection, the button illumination time brighter and darker. The plushels start automatically demanding on the device tube / device

Bluetooth

Connect

BTC...

Pause

With a press of a button, the playback of the connected audio source is interrupted.

Deleting connections

With a long press of a button (> 10 s), all previously taught-in audio sources are deleted from the Bluetooth Connect.

Intended use

• Installation in a flush-mounted device box according to DIN EN 49073 (recommended: deep box)
• Bluetooth Connect for audio output in conjunction with a playback device and for media control

Product characteristics

• Bluetooth Connect with sensor buttons
• Solid glass front
• Stereo playback
• Connecting terminals for two loudspeakers
• Stereo/mono change over
• Easy operation
  • High reception quality
• Integrated amplifier
  • Storage of 6 audio sources
• Switching on with the last audio source
• Switching on with the last volume
• Extension unit input

Installation

Technical line drawing of a mechanical device with no visible text or symbols

The Bluetooth Connect BTC... has been designed for installation in device boxes DIN EN 49073.

The connections for mains voltage, loudspeakers and the audio output are located on the flush-mounted power supply unit. The operating cover together with the frame are mounted onto the power supply unit.

Connecting an extension unit

The extension unit connection (1) is used to switch the Bluetooth Connect on/off via switches, e.g. together with the light. The extension unit input may only be operated on the same phase.

Before carrying out work on the device, disengage all the corresponding circuit

Cleakers. Cover up live parts in the working environment. Within the device

box, all the cables carrying low voltages must have an insulating hose in order

to guarantee protective separation

Connecting a loudspeaker

The device is intended for operation with one or two loudspeaker modules LSM.... The connection cable can be up to 5 m long.

In stereo mode, both outputs (L+R) are used. The device detects autonomously if only one loudspeaker is used and then changes its operating mode to mono.

The correction of several loudspeakers per output is not permitted.

Loudspeakers of other manufacturers may only be used if the technical data is identical with the JUNG LSM.

Please observe the polarity.

Technical data

Rated voltage: AC 230 V \~

Frequency: 50/60 Hz

Power consumption in standby. 0.37 W

Power consumption in operation: < 4.00 W

Ambient temperature: 0...+50 °C

Atmospheric humidity: 15% ... 90%

no condensation

Bluetooth: A2DP, AVRCP

Degree of protection: IP 20

Connection Screw terminals

1×1.5 mm² or 1×2.5 mm²

Connecting cable loudspeaker

Twin cable H03VH-H, 2 x 0.75 mm²

alternative:

JY-(St)- Y 2x2x0.6

Length: max. 5 m

Loudspeaker LSM.

Rated load capacity: 2.5 W

Impedance: 4 Ω

Frequency range 20 .. 15000 Hz (-10 dB)

Line-out (AUX):

Impedance: 470 Ω

Output level: 1V

is a trademark of the

both SIG, Inc.