ST-BTWD700IR2812 - Security Camera Security Tronix - Free user manual and instructions

Product Type	Security Camera
Brand	Security Tronix
Model	ST-BTWD700IR2812
Image Sensor	1/3" Sony Super HAD CCD
Effective Picture Elements	811 (H) x 508 (V)
Horizontal Resolution	700 TV Lines
Minimum Illumination	0.001 Lux (with IR LEDs ON)
Signal-to-Noise Ratio	>48 dB
Scanning System	2:1 Interlace
Sync System	Internal, Negative Sync
IR LEDs	36 LEDs
IR Range	Up to 160 feet
Power Supply	12 V DC (min 0.8 A) or 24 V AC (min 0.5 A)
Weatherproof Rating	IP66
Day/Night Function	Yes (with IR cut filter)
Wide Dynamic Range	Yes
OSD Menu	Yes
Lens Adjustment	Zoom and focus via rear knobs
Mounting	3-axis bracket, extension tube for ceiling
Included Accessories	Extension tube, hex wrench, anchors/screws, manual
Housing Color	Black or White
Warranty	Standard factory warranty (serial number required)

Frequently Asked Questions - ST-BTWD700IR2812 Security Tronix

How do I adjust the zoom and focus on the ST-BTWD700IR2812?

The zoom and focus adjustments are made via two knobs on the rear panel of the camera. Do not loosen the screws holding the knobs, as this may cause the adjustment rod to fall inside and void the warranty. Use pliers if the knobs are difficult to turn by hand.

What power supply is required for this camera?

The camera requires a 12 V DC power supply with a minimum current of 800 mA (0.8 A) or a 24 V AC power supply with a minimum current of 500 mA (0.5 A). Always use a power supply that meets or exceeds these specifications to avoid voltage drop issues.

What is the infrared range of the ST-BTWD700IR2812?

With 36 built-in IR LEDs, the camera can provide clear images in total darkness up to 160 feet.

What should I do if I get no picture after powering on?

First, check that all plugs and cables are securely connected to the proper connectors. Second, ensure your power supply is providing the correct voltage and current (12V DC ≥0.8A or 24V AC ≥0.5A).

What does the IP66 rating mean?

IP66 means the camera is dust-tight and protected against powerful water jets, making it suitable for outdoor use in all weather conditions.

Can I use this camera outdoors?

Yes, the camera has an IP66 weatherproof rating and is designed for outdoor installation. Ensure all connections are properly sealed to maintain weather resistance.

How do I clean the camera?

Use a soft, dry cloth to clean the housing and lens. Avoid using solvents or abrasive cleaners. Do not disassemble the camera, as breaking the weather seal may allow humidity to enter and cause image issues.

What is the warranty and how do I claim it?

The camera comes with a standard factory warranty. You need the serial number (on the camera label) to determine warranty eligibility. For assistance, contact your distributor or Security Tronix at 1-800-688-9282.

How can I contact technical support?

Call 1-800-688-9282, press 3 for Tech Support, then press 2 for Security Tronix Tech Support. Additional resources are available at www.securitytronix.com.

What is the horizontal resolution of this camera?

The camera delivers 700 TV lines of horizontal resolution, providing sharp and detailed images.

USER MANUAL ST-BTWD700IR2812 Security Tronix

INSTALLATION MANUAL

ST-BTWD700IR2812 B or W Weatherproof Day/Night Infrared Color Camera

PACKAGE CONTENTS

This package contains:

One ST-BTWD700IR2812 camera with Black or White housing

One extension tube for mounting on a ceiling

One installation manual

One hex wrench for adjusting the mounting bracket

Four anchors and screws to mount the camera

NOTE: The ST-BTWD700IR2812 camera requires a 12 volts DC power with a minimum current of 800 milliamps (.8 Amps) or a 24 volts AC power supply with a minimum current of 500 milliamps.

PRODUCT DESCRIPTION

The ST-BTWD700IR2812 is an IP66 rated, weatherproof day / night infrared color camera designed around a 1/3" color Sony Super HAD CCD image sensor with 700 TV Lines of resolution. The 36 infrared LEDs provide an image in total darkness up to 160 feet. The camera can be easily installed in most orientations with the included 3-axis bracket. With Wide Dynamic Range, versatile OSD menu settings, rich color saturation and 700 lines of resolution, the ST-BTWD650IR2812 camera is a versatile, high quality addition to any surveillance application.

SPECIFICATIONS (Typical)

Image sensor element 1/3" Sony Super HAD CCD
Effective Picture Elements 811(H) x 508(V)
Horizontal Resolution 700TVL
Minimum Illumination 0.001 Lux (with IR LEDs ON)
S/N Ratio >48dB
Scanning System 2:1 Interlace
Sync System Internal, Negative Sync

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electric shock and/or damage to the camera, do not disassemble this camera or open the casing. There are no user-serviceable parts inside and breaking the camera's weather seal may allow humid air to enter the camera which can cause a foggy or washed-out image. Always use a power supply which meets the specified voltage and meets or exceeds the specified current. Voltage drop over a cable's length should always be taken into consideration.

UNPACKING AND HANDLING

Each unit is shipped fully assembled and factory tested. There is no need to open the housing of the camera and doing so will void the warranty.

Ensure that all accessories are removed from the box before discarding the packing material.

Take care to ensure that the label with the camera's serial number is not removed or damaged. The serial number is needed to determine whether or not a camera is under warranty.

MECHANICAL INSPECTION

Inspect the camera for signs of shipping damage. Ensure that the equipment is clean and that no connections are damaged or loose. If the camera appears to be damaged or defective, call your distributor or SecurityTronix at 1 [phone] for assistance.

SPECIAL ATTENTION

- The installer must comply with electrical safety standards - There must be sufficient space between the camera's power supply and video line and any high voltage

LENS ADJUSTMENTS

Zoom and focus adjustments are made via 2 knobs on the rear panel of the camera.

NOTE: The tension of these knobs is set at the factory for maximum weather protection. Do not loosen the screws which hold the knobs in place. This could cause the adjustment rod to fall inside the camera and will void the warranty. If the screws are difficult to turn by hand, pliers may be used.

TROUBLESHOOTING

• No picture after applying power (i) check all plugs and cables are securely connected to the proper connectors; (ii) ensure your power supply is providing the correct voltage and current.
• The picture has ripples (i) check to see if the power supply is experiencing AC ripple, if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if other peripheral equipment is causing ripple and if so make the necessary adjustments.
• The picture background continuously changes color. A fluorescent lamp's magnetic field may cause color roll. First try turning on the camera's color roll feature. If the problem persists, reduce the number of fluorescent lamps or increase the distance between the camera and the lamps.
• The picture appears smeared. (i) the power supply voltage level may be unstable, try another power supply; (ii) ensure the cables are correctly connected and (or the cables are of the correct impedance.
• Other interference may require a SecurityTronix ground loop isolation filter.

Additional troubleshooting assistance can be found on-line at www.securitytronix.com in addition to support from Securitytronix Tech Engineers at 1-800-688-9282.

Press "3" for Tech support, then press "2" for SecurityTronix Tech Support