Freedom Cyc - Effects machine Chauvet - Free user manual and instructions

Product Type	Battery-powered LED wash light
Dimensions (L x W x H)	7.5 x 5.8 x 5.4 in (191.2 x 148.2 x 138 mm)
Weight	7.2 lb (3.3 kg)
Power Supply	Auto-ranging 100-240 VAC, 50/60 Hz
Power Consumption	64 W (120V), 61 W (230V)
Battery Type	Rechargeable lithium battery
Battery Run Time	Not specified in manual (estimated several hours)
Light Source	4 x 48W quad-color LEDs (RGB+WW)
LED Lifespan	50,000 hours
Beam Angle	52°
Field Angle	95°
Strobe Rate	0 to 22 Hz
DMX Channels	4, 6, or 10 channels
DMX Connector	IEC power input, no DMX in/out specified (wireless only)
Wireless DMX	D-Fi 2.4 GHz, 16 channels, transmit/receive
Control	On-board menu, IRC-6 infrared remote (included)
Mounting	Any orientation, rigging with safety cable, mounting clamp
Cooling	Convection, keep 20 in (50 cm) clearance
Max Ambient Temperature	104 °F (40 °C)
IP Rating	IP20 (indoor use only)
Power Linking	Up to 15 units (120V) or 29 units (230V)
Included Accessories	Power cord, IRC-6 remote, Quick Reference Guide
Cleaning	Vacuum or dry compressed air; mild soap for transparent surfaces
Safety	Grounded circuit, safety cable required for overhead mounting

Frequently Asked Questions - Freedom Cyc Chauvet

How do I charge the battery?

Connect the built-in charger to a power source while the product is turned off. Avoid charging in a closed container. Allow a fully depleted battery to charge for a few minutes before turning on.

What is the battery life indicator?

The LED menu display shows battery level. Deplete the battery below 10% for best results.

How do I set up wireless DMX?

Set the transmitting product to dtCH and choose a channel (1-16). Set receiving product(s) to drCH and match the channel. Ensure all slaves are configured before the master.

What DMX personalities are available?

The Freedom Cyc can be set to 4Ch (RGBW), 6Ch (RGBW + dimmer + strobe), or 10Ch (full control including color temperature and auto programs).

Can I use the IRC-6 remote control?

Yes, the Freedom Cyc is compatible with the included IRC-6 infrared remote. Enable IR mode in the menu (IR Setting > On).

How do I clean the fixture?

Unplug and wait until cool. Use vacuum or compressed air for vents. Clean transparent surfaces with mild soap or isopropyl alcohol on a soft cloth. Avoid abrasive cleaners.

What is the maximum ambient temperature for operation?

Do not operate above 104 °F (40 °C). Ensure adequate ventilation, at least 20 inches from adjacent surfaces.

Can the product be mounted in any orientation?

Yes, but always ensure proper ventilation. When mounting overhead, use a safety cable and appropriate clamp.

How many units can be power linked?

Up to 15 units at 120V or 29 units at 230V. Do not exceed the maximum linked units.

What should I do if the battery gets hot during charging?

It is normal for the device to heat up, but if it becomes unusually hot, the charger may stop. Do not charge in a closed container or for more than 24 hours.

USER MANUAL Freedom Cyc Chauvet

TABLE OF CONTENTS

1. Before You Begin .... 1

What Is Included 1
Unpacking Instructions.... 1
Text Conventions 1
Symbols 1
Disclaimer 1
Safety Notes 2

1. Introduction ...... 3

Product Overview 3
Product Dimensions 4

1. Setup 5

AC Power 5
Battery Power 5

Charging the Battery 5
Battery Charge Notes 5
Battery Life Indicator 5
Battery Run Time 5

Mounting 6

Orientation.... 6
Rigging 6

1. Operation 7

Control Panel Operation.... 7
Menu Map 7

Wireless DMX Linking 9

DMX Personality and Starting Address.... 9
Wireless DMX Configuration 9

DMX Channel Assignments and Values 10

10Ch.... 10
6Ch.... 11

4Ch.... 11

Configuration (Standalone) 11

Static Mode

1. Before You Begin

What Is Included

- Freedom Cyc

- Power cord

- IRC-6 remote

• Quick Reference Guide

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Claims

If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Text Conventions

Convention Meaning
1-512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
A key to be pressed on the product's control panel
ON A value to be entered or selected
Symbols
Symbol Meaning

i

Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
Important installation or configuration information. The product may not function correctly if this information is not used.

Safety Notes

• Always connect the product to a grounded circuit to avoid the risk of electrocution.

• Always disconnect the product from the power source before cleaning or replacing the fuse.

- Avoid direct eye exposure to the light source while the product is on.

- Make sure the power cord is not crimped or damaged.

• Never disconnect the product from power cord by pulling or tugging on the cord.

- If mounting the product overhead, always secure to a fastening device using a safety cable.

- Make sure there are no flammable materials close to the product when operating.

- Do not touch the product's housing when operating because it may be very hot.

- Do not charge the battery of the product in a closed case or container.

• Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product.

- The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.

• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.

- Be sure that no ventilation slots on the product's housing are blocked.

- Never connect the product to a dimmer.

• Make sure to replace the fuse with another of the same type and rating.

- Never carry the product from the power cord or any moving part. Always use the hanging/mounting bracket.

- The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher temperatures.

- In the event of a serious operating problem, stop using the product immediately.

- Never try to repair the product. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Keep this User Manual for future use. If you sell the product to someone else, be sure that they also receive this document.

2. Introduction

Product Overview

Product Dimensions

Setup

3. Setup

AC Power

This product has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz.

To eliminate unnecessary wear and improve its lifespan, completely disconnect the product from power via breaker or by unplugging it during periods of non-use.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

Battery Power

The Freedom Cyc comes with a rechargeable lithium battery for cable-free operation.

Charging the Battery

The battery charges whenever the Freedom Cyc's built-in charger is plugged into a power source. If the product is plugged in and not in operation, make sure the product is turned off.

- Charge the Freedom Cyc while the unit is powered OFF.

- Do not charge the battery of the product in a closed case or container.

Battery Charge Notes

• Avoid depleting the battery below 10%.
  • For best results, charge the battery in a temperature between 32 °F (0 °C) and 95 °F (35 °C).
• When charging the battery, keep the product at least 1 m from any open flame or hot plate.
• If the battery is completely discharged, the device cannot be turned on immediately when the charger is connected. Allow a depleted battery to charge for a few minutes before turning on the device.
• While charging, the device may heat up. This is normal and should not affect the device's lifespan or performance. If the battery gets hotter than usual, the charger may stop charging.
• Do not charge the battery in a closed container.
• Do not charge the battery for more than 24 hours.

Battery Life Indicator

The indicators on the LED Menu Display show how much battery life remains available. The drawing below provides a key to reading the battery life indicators.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation

The Freedom Cyc may be mounted in any position; however, make sure adequate ventilation is provided around the product.

Rigging

• Before deciding on a location, always make sure there is easy access to the product for maintenance and programming purposes.
• Make sure adequate ventilation is provided around the product.
  • Make sure that the structure or surface onto which you are mounting the product can support the product's weight. (see the Technical Specifications)
• When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, such as an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power-linking cables to reach.
• The bracket adjustment knob allows for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knob manually. Using tools could damage the knob.

Mounting Diagram

4. Operation

Control Panel Operation

To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.

Button Function
	Exits from the current menu or function
	Navigates upwards through the menu list and increases the numeric value when in a function
	Navigates downwards through the menu list and decreases the numeric value when in a function
	Enables the currently displayed menu or sets the currently selected value into the selected function

Menu Map

Main Level Programming Levels Description
DMX Address	Address 000-512		Selects starting address (‘highest channel restricted to personality chosen)
DMX Channel	4Ch		Sets DMX personality 6Ch
	10Ch
	Fixed Color	R Red
		G Green
		B Blue
		W White
		GB Green + Blue
		RB Red + Blue
		RG Red + Green
		RGB Red + Green + Blue
		RW	Red + White
		GW	Green + White
		BW	Blue + White
		RGW	Red + Green + White

Operation

Main Level Programming Levels Description
Auto Show	Auto 1		1-100	Selects automatic programs and auto program speed
	Auto 2
	Auto 3
	Auto 4
White Balance	Off Uses factory default white setting
	Manual	Red		Sets red LED maximum value
		Green Sets green LED maximum value
		Blue Sets blue LED maximum value
		White Sets white LED maximum value
Wireless Setting	Wireless On/Off		On	Turns wireless setting on and off
			Off
	Wireless Mode		Transmit	Turns on wireless DMX and sets transmitter or receiver channel
			Receive
	Wireless Channel CH01-CH16 Selects available wireless channel
IR Setting	On			Turns infrared on or off
	Off
Dimmer Mode	Off			Sets the dimming speed to fast (Dimmer 1) or slow (Dimmer 3) or no dimmer (Off)
	Dimmer 1
	Dimmer 2
	Dimmer 3
Back Light	10S			Turns off display backlight after 10 seconds of inactivity
	30S			Turns off display backlight after 30 seconds of inactivity
	2Min			Turns off display backlight after 2 minutes of inactivity
	Always On Display backlight always on
Information	Fixture Hours _ _ _ | Shows total product hours
	Version V._ Shows installed software version
Factory Reset	No			Reset to factory defaults
	Yes

Operation

Wireless DMX Linking

The Freedom Cyc works with a DMX controller in Wireless DMX mode. In wireless DMX mode, a lighting control board or D-Fi product, such as the optional FlareCON Air controller, must send wireless DMX signals to the products. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website: http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.

DMX Personality and Starting Address

When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product's channels.

The Freedom Cyc uses up to 10 DMX channels, which defines the highest configurable address as 503. If you are not familiar with the DMX protocol, download the DMX Primer from www.chauvetdj.com.

To select the starting address, do the following:

1. Press until DMX Address shows on the display.
2. Press until Address appears, then press again.
3. Use or to select starting address, from 001-503.
4. Press

To set the DMX channel, do the following:

1. Press repeatedly until DMX Channel shows on the display.
2. Press .
3. Use or to select the DMX channel: 4Ch, 6Ch, or 10Ch.
4. Press

Wireless DMX Configuration

The Freedom Cyc offers wireless control of two or more products with a single DMX controller. To set up the D-Fi 2.4 GHz transceiver, follow the instructions below.

For the transmitting product:

1. Press repeatedly until S-tr shows on the display.
2. Press
3. Use or to select dtCH.
4. Press
5. Use or to select the D-Fi channel, from dt 1-16.
6. Press

For the receiving product(s):

1. Press repeatedly until S-tr shows on the display.
2. Press

DMX Channel Assignments and Values
10Ch

Channel Function Value Percent/Setting
1 Dimmer 000 ⇔ 255 0–100%
2 Red 000 ⇔ 255 0–100%
3 Green 000 ⇔ 255 0–100%
4	B	I	u	e	0 0 0 ⇔ 255 0–100%
5 White 000 ⇔ 255 0–100%
6 Color Temperature			000 ⇔ 005		No function
			006 ⇔ 030		2800K
			031 ⇔ 055		3000K
			056 ⇔ 080		3200K
			081 ⇔ 105		3500K
			106 ⇔ 130		4000K
			131 ⇔ 155		4500K
			156 ⇔ 180		5000K
			181 ⇔ 205		5600K
			206 ⇔ 230		6000K
			231 ⇔ 255		6500K
7	S	t	r	o	b 000 ⇔ 010 No function
					e 011 ⇔ 255 Strobe (slow to fast)
8 Auto Programs			000 ⇔ 010 No function
			011 ⇔ 060 Auto program 1
			061 ⇔ 120 Auto program 2
			121 ⇔ 180 Auto program 3
			181 ⇔ 240 Auto program 4
			241 ⇔ 255 Sound-active program
9	A	u	t	o	000 ⚫ 255 Auto program speed (slow to fast)
10 Dimmer Speed Mode			000 ⇔ 051 Preset dimmer speed from display menu
			052 ⇔ 101 Dimmer speed mode off
			102 ⇔ 152 Dimmer speed mode 1 (fast)

Operation

6Ch

Channel Function Value Percent/Setting
1 Dimmer 000 ⇔ 255 0–100%
2 Red 000 ⇔ 255 0–100%
3 Green 000 ⇔ 255 0–100%
4	Blue	000 ⇔ 255	0–100%
5	White	000 ⇔ 255	0–100%
6	S t r o b	000 ⇔ 010	No function
		011 ⇔ 255	Strobe (slow to fast)

4Ch

Channel Function Value Percent/Setting
1 Red	000 ⇔ 255 0–100%
2 Green	000 ⇔ 255 0–100%
3	Blue	000 ⇔ 255	0–100%
4	White	000 ⇔ 255	0–100%

Configuration (Standalone)

Set the product in one of the standalone modes to control without a DMX controller.

Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.

Static Mode

Fixed Color

To run the Freedom Cyc on a static color, follow the instructions below:

1. Press repeatedly to select Static from the menu list.
2. Press
3. Use or to select Fixed Color.
4. Press
5. Use or to select a fixed color (red, green, blue, white, and RGBW combinations).
6. Press .

Automatic Programs

To run the Freedom Cyc in automatic mode, follow the instructions below:

1. Press repeatedly to select Auto Show from the menu list.
2. Press
3. Use or to select an automatic program, from Auto 1-4.
4. Press
5. Use or to increase or decrease the program speed, from 1–100.
6. Press . The product will return to the last selected mode.

White Balance

To adjust the white color setting, follow the instructions below:

1. Press repeatedly to select White Balance from the menu list.
2. Press .
3. Use or to select between Off and Manual setting.
4. Press

For Manual setting:

1. Use or to select from Red, Green, Blue, or White.
2. Press
3. Use or to increase or decrease the color value, from 125–255.
4. Repeat steps 1–3 until the product outputs as desired.

Dimmer Mode

To set the dimmer curve, follow the instructions below:

1. Press repeatedly to select Dimmer from the menu list.
2. Press
3. Use or to select from Dimmer1-3 or Off.
4. Press . The product will return to the last selected mode.

Back Light

To set the timer for the back light, follow the instructions below:

1. Press repeatedly to select Back Light from the menu list.
2. Press
3. Use or to select from 10S, 30S, 2Min, or Always On.
4. Press . The product will return to the last selected mode.

Information

Operation

IRC-6 Infrared Remote Control

The Freedom Cyc is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR mode, follow the instructions below:

1. Press repeatedly until IR Setting shows on the display.
2. Press to accept.
3. Press or to select On or Off.
4. Press

IRC-6 Operation

Automatic Mode

Automatic mode will enable you to run the automatic programs on the product.

To turn on Automatic mode:

1. Press on the IRC-6

2. Press <+> or <-> to choose between the different auto programs.

To select only fading programs:

1. Press on the IRC-6.

2. Press <+> or <-> to choose between the different fading programs.

To adjust the speed of the automatic program:

1. Press on the IRC-6.

2. Press <+> or <-> to increase or decrease the speed of the program.

Manual Color Control

To select a preset static color with the IRC-6:

1. Press <1>-<9> on the IRC-6.

To custom-mix a color with the IRC-6:

1. Press on the IRC-6, or skip to step 2.
2. Select the color to be edited, from (red), (green), (blue),
   (amber), (UV), or . (white)
3. Press <+> or <-> to increase or decrease the value of the selected color.
4. Repeat steps 2 and 3 until the product outputs as desired.

Strobe

To adjust the strobe rate:

1. Press on the IRC-6.
2. Press <+> or <-> to increase or decrease the strobe rate.
3. Press again to turn off the strobe.

Dimme

To adjust the total output with the IRC-6:

The Master/Slave mode allows a single Freedom Cyc product (the "master") to control the actions of one or more Freedom Cyc products (the "slaves") without the need of a DMX controller or DMX cables. The master (transmitter) product will be set to operate in either Stand-Alone mode or with the IRC-6, while the slave (receiver) products will be set to operate in Slave mode. Once set and connected, the slave products will operate in unison with the master product.

Configure the products as indicated below.

Slave products:

1. Press repeatedly until S-tr shows on the display.
2. Press
3. Use or to select drCH.
4. Press
5. Use or to select the receiving D-Fi channel, from dr 1-16.
6. Press
7. Finish setting all the slave products.

Master product:

1. Press repeatedly until S-tr shows on the display.
2. Press
3. Use or to select dtCH.
4. Press
5. Use or to select the transmitting D-Fi channel on which the slave products are receiving, from dt 1–16.
6. Press
7. Set the master product to operate in Stand-Alone mode or with the IRC-6.

• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master.

5. Maintenance

Product Maintenance

Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source's life and/or mechanical wear. To maintain optimum performance and minimize wear, clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.

To clean the product, follow the instructions below:

1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.

Always dry the transparent surfaces carefully after cleaning them.

6. Technical Specifications

Dimensions and Weight

Length Width Height Weight

7.5 in (191.2 mm) 5.8 in (148.2 mm) 5.4 in (138 mm) 7.2 lb (3.3 kg)

Note: Dimensions in inches rounded to the nearest decimal digit.

Power
Power Supply Type	Range	Voltage Selection	Input Voltage
Switching (external)	100 to 240 VAC, 50/60 Hz	Auto-ranging	8.4 VDC, 1.3 A
Parameter	120 V, 60 Hz		230 V, 50 Hz
Consumption	64 W		61 W
Operating current	0.5 A		0.2 A
Power linking	15 units		29 units
Power I/O	U.S./Worldwide		UK/Europe
Power input connector	IEC		IEC
Power cord plug	Edison (U.S.)		Local plug

Light Source

Type	Color	Quantity	Power	Current	Lifespan
LED	Quadcolor (RGB+WW) x 4	16	48 W	3.5 A	50,000 hours

Photometrics

Strobe Rate	Beam Angle	Field Angle	Illuminance @ 2m
0 to 22 Hz 52°	95°	418 lux

Thermal

Maximum External Temperature	Cooling System
104 °F (40 °C)	Convection

DMX

I/O Connector Channel Range

Returns

In case you need to get support or return a product:

• If you are located in the U.S., contact Chauvet World Headquarters.
  • If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
  • If you are located in Benelux, contact Chauvet Europe BVBA.
  • If you are located in France, contact Chauvet France.
  • If you are located in Germany, contact Chauvet Germany.
  • If you are located in Mexico, contact Chauvet Mexico.
  • If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See www.chauvetdj.com for distributors outside the U.S., UK, Ireland, Benelux, France, Germany, or Mexico.

If you are located outside the U.S., UK, Ireland, Benelux, France, Germany, or Mexico, contact your distributor of record and follow their instructions on how to return Chauvet products to them. Visit our website www.chauvetdj.com for contact details.

Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return.

To submit a service request online, go to www.chauvetdj.com/service-request.

Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet will not issue call tags.

Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA number.

Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.

Before sending the product, clearly write the following information on a piece of paper and place it inside the box:

• Your name
• Your address
• Your phone number
  • R M A n u m b e r
  • A brief description of the problem

Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended.

Chauvet reserves the right to use its own discretion to repair or replace returned

Contact Us

General Information Technical Support

World Headquarters

Address: 5200 NW 108th Ave. Voice: [phone]Sunrise, FL 33351 Fax: [phone]Voice: [phone] Email: [e-mail]: [phone]Toll Free: [phone] Website: www.chauveldj.com

UK

Address: Unit 1C Email: [e-mail] Road Industrial EstatePinxton, Nottingham, UK Website: www.chauveldj.euNG16 6NTVoice: [phone]Fax: [phone]

Benelux

Address: Stokstraat 18 Email: [e-mail]9770 KruishoutemBelgium Website: www.chauvetdj.euVoice: [phone]

France