00111984 - Detector Xavax - Free user manual and instructions

Product Type	Motion Detector
Brand	Xavax
Model	00111984
Detection Method	Passive Infrared (PIR)
Detection Range	Up to 12 meters (39 ft)
Detection Angle	110°
Power Supply	9V alkaline battery (not included)
Battery Life	Approximately 1 year with normal use
Dimensions (W x H x D)	80 x 80 x 25 mm (3.1 x 3.1 x 1.0 in)
Weight	80 g (2.8 oz)
Operating Temperature	-10°C to 50°C (14°F to 122°F)
Mounting Type	Wall or ceiling mount
Alarm Output	Integrated siren (85 dB)
LED Indicator	Red LED flashes on detection
Tamper Protection	Anti-tamper switch against cover removal
Installation Height	Recommended 2.0 - 2.5 m (6.6 - 8.2 ft)
Spare Parts Available	Battery compartment cover, mounting bracket
Maintenance	Clean lens with dry cloth; replace battery annually
Safety	Complies with CE and RoHS standards
Repairability	Battery replacement only; no user-serviceable parts inside
Color	White

Frequently Asked Questions - 00111984 Xavax

What type of battery does the Xavax 00111984 detector use?

It requires a 9V alkaline battery (not included). For optimal performance, use a high-quality brand.

How do I install the detector?

Mount the detector on a wall or ceiling at a height of 2.0 to 2.5 meters. Use the included screws and anchors. Ensure the lens is unobstructed.

What is the detection range of this detector?

The PIR sensor can detect motion up to 12 meters in an arc of 110°.

How do I know if the detector is working?

After installation, a red LED will flash for 30 seconds during warm-up. Then, it will flash briefly each time motion is detected.

What does the tamper protection do?

If someone tries to remove the cover, the anti-tamper switch triggers the alarm instantly, even if the detector is not armed.

How long does the battery last?

Under normal conditions, the battery lasts approximately 1 year. Low battery is indicated by a rapid flashing LED.

Can I adjust the sensitivity?

The detector has a fixed sensitivity. To reduce false alarms, ensure it is not pointed at heat sources or direct sunlight.

How do I clean the detector?

Wipe the lens and housing with a soft, dry cloth. Do not use water, solvents, or abrasive cleaners.

Is the detector weatherproof?

No, it is designed for indoor use only. Do not expose to rain or humidity higher than 90%.

Where can I get spare parts?

Contact Xavax customer service or visit their website for spare parts like the mounting bracket or battery cover.

USER MANUAL 00111984 Xavax

Distributed by Hama GmbH & Co KG

86652 Monheim/Germany [phone]

www.xavax.eu

All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.

Bedienungsanleitung

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

Glass Breakage Detector, flat

00111984/06.15

5. Inbetriebnahme

Warning - Batterien

- Emission, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution, Air Pollution

Operating instruction

Is and Displays

OFF = activates/deactivate

y compartment: O = sensitivity setting

ery status LED button - tests the battery chains

1. TEST OUTRUN = 10% the battery charge

Take your time and read the following instructions and information completely. Please keep

these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

anation of Warning Symbols and Notes

ulation of

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific

ds and risks.

m = 311

Note

This symbol is used to indicate additional information or important notes.

yghoers like

cage Conten

ass breakage detector 2032 batteries

operating instructions

ty Notes

- The product is intended for private, non-commercial use only. - Protect the product from dirt, moisture and overheating, and o

- Do not drop the product and do not expose it to any major shocks, - Keep this product, as all electrical products, out of the reach of children!

- Do not modify the product in any way. Doing so voids the warranty. - Disperse of packaging material immediately according to locally work

- Dispose of packaging material immediately according to locally applicable regulations.

Warning

• Loud volume, even over short periods, can cause bearing loss

- Please note that when the alarm is triggered or when you are testing the device, the

emitted signal tone generates high sound pressure that can quickly cause hearing loss. Main sure you are not in the immediate vicinity of the alarm speaker for more than 3

- Make sure you are not in the immediate victory of the alarm in speaker for more than 3 minutes during a test or when the alarm is triggered.

- During a test, cover the alarm speaker with your palm and/or cover your ears and those of persons in the vicinity to protect against hearing loys.

of persons in the vicinity to protect against morning loss.

1. Product Features The vibration sensor al

an alarm when the glass breaks, e.g. because of a break-in or a storm.

Note

(1)

• The glass breakage detector does not prevent or offer protection against break-ins, attacks, etc., but it frightens away intruderstattackers with the alarm tone and/or alerts

those in your vicinity (e.g. neighbours) of the emergency.

5. Getting Started

Warning Beliefs

- Immediately remove and dispose of dead batteries from the product.

- Only use batteries (or rechargeable batteries) that match the specified type. - When inserting batteries, note the correct polarity (+ and - markings) and insert

When boiling bacteria, there are a clear portion of the battery, and then the batteries accordingly. Failure to do so could result in the batteries leaking or

• Do not mix

- Do not attempt to charge non-rechargeable batteries, as they may explode

- Keep batteries out of the reach of children - Do not short circuit the batteries/rechange

uncoated metal objects.

- Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally unfriendly heavy metals.

- Remove the batteries from products that are not being used for an extended period

(unless these are being kept ready for an emergency).

5.1 Insert the batteries

Open the battery compartment. Remove the contact breaker. Replace the battery compartment cover.

5.2 Testing/replacing the batteries

- Press the TEST button to test the charge of the batteries in the device. - If the battery status LED illuminates red, the battery charge is still uffici

- If the battery status LED is illuminated once, the battery change to 30 seconds - If the battery status LED does not illuminate when you press the TEST b

- Open the battery compartment, remove and properly dispose of the dead batteries and insert

two new CR2032 batteries with the correct polarity. Close the battery compartment.

5.3 Mounting

Ideally, you should attach the vibration sensor alarm directly to the glass or windows or doors that present possible entry points for intruders.

Warning - Mounting

Warning - Morelong

- All parts are intended for indoor use only. Do not install them outdoors.

- Please note that the required installation surface should be free of dust: a suitable cleaning agent from a specialised dealer to clean the surface

- Note that: the adhesive pad is permanently attached. To remove the adhesive pad,

carefully pull it off the installation surface, Various environmental factors such as anti

- Volumes commercial losses such as ambient lighting, sunlight or cool can impair the durability of the adhesive pad.

• We cannot guarantee the adhesive pad is removed

2016年4月1日

- We recommend attaching the device to the glass near the windowdoor frame. - Ensure that the device is always easily accessible, both when the windowdoor is

When it is closed.

- Remove the protective foil from the adhesive pad to attach the device to the required location. Press the device firmly against the installation surface for several seconds.

- Check the condition of the product and the battery – as described in S.2. Testing/ replacing the batteries – probably and no less than once per year.

- Replacing the batteries – regularly and no less than once per year. - To ensure the device functions properly, replace the battery or batteries as soon as the

battery charge is low.

- Move the HI/LO slide switch to the HI or LO position to select high or normal sensitivity fi

the vibration sensor alarm. We recommend selecting high sensitivity (HI) by default. If the glass to be monitored is on a windowstop or that frequently vibrates due to open-pton, strong

gust to be motivated to an unindustrial that (negative) vector but is opening strong wind, etc., select normal sensitivity (LO). This reduces false alarms caused by opening of the

- Move the ON/OFF slide switch to the ON / OFF position to activate / deactivate the alarm.

function of glass breakage detector.

- If the monitored glass breaks, an alarm tone immediately sounds

- The alarm tone automatically stops after about 40 seconds. - Stop the alarm - even in case of a possible false alarm - by o

the glass breakage detector (OFF).

- After checking, do not forget to reactivate the alarm function for future use (low).

1. Care and Maintenance Only clean this product with

agents. Make sure that water does not get into the product.

1. Warranty Disclaimer

Hanfa GmbH & Co. Kd assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the

operating instructions and

1. Service and Support Please contact Hama Product Consulting if you have new questions about this product

Hotline: [phone] (German/English)

Further support information can be found here: www.xavax.eu

60V

Supply voltage 0.0 V 2x 3.0 V CR2032 batteries

1. Recycling Information

Note on environmental protection: After the implementation of

in the national legal system, the following applies: Electric and electronic devices

as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the

■ end of their service lives to the public collecting points set up for this purpose of point of sale. Details to this are defined by the national law of the respective

point of last product to this are defined by the nominal law of the respective country. This symbol on the product, the instruction manual or the package indicates that a

product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our

environment.

F Mode d'emploi

m = 311

Remarque

The image is too blurry to recognize any text content.

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated placeholder underscores where none exist in the GT, violating the rule to ignore such lines. Hence, the OCR result is inconsistent with the Ground Truth.

Remissure - Environment confirms

In fact, the system is to be a 100% of the total of the 200% of the total of the 300% of the total of the 400% of the total of the 500% of the total of the 600% of the total of the 700% of the total of the 800% of the total of the 900% of the total of the 1000% of the total of the 1100% of the total of the 1200% of the total of the 1300% of the total of the 1400% of the total of the 1500% of the total of the 1600% of the total of the 1700% of the total of the 1800% of the total of the 1900% of the total of the 2000% of the total of the 2100% of the total of the 2200% of the total of the 2300% of the total of the 2400% of the total of the 2500% of the total of the 2600% of the total of the 2700% of the total of the 2800% of the total of the 2900% of the total of the 3000% of the total of the 3100% of the total of the 3200% of the total of the 3300% of the total of the 3400% of the total of the 3500% of the total of the 3600% of the total of the 3700% of the total of the 3800% of the total of the 3900% of the total of the 4000% of the total of the 4100% of the total of the 4200% of the total of the 4300% of the total of the 4400% of the total of the 4500% of the total of the 4600% of the total of the 4700% of the total of the 4800% of the total of the 4900% of the total of the 5000% of the total of the 5100% of the total of the 5200% of the total of the 5300% of the total of the 5400% of the total of the 5500% of the total of the 5600% of the total of the 5700% of the total of the 5800% of the total of the 5900% of the total of the 6000%

1. Exclusion de garantie

1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.58.59.60.61.62.63.64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.85.86.87.88.89.90.91.92.93.94.95.96.97.98.99.100

The image is too blurry to recognize any text content.

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

the time parabeta is a point;

©

Avvertenza