95-6506B - Car kit Metra - Free user manual and instructions

Product Type	Vehicle Wiring Harness
Brand	Metra
Model	95-6506B
Compatible Vehicles	Select General Motors cars and trucks (1998-2005)
Application	Aftermarket stereo installation
Wiring Function	Connects aftermarket radio to vehicle's factory wiring
Connector Type	Plug-and-play with factory connectors
Color Coding	Standard aftermarket wire colors (ISO/DIN)
Wire Gauge	18 AWG typical
Length	Approximately 8 inches (20 cm) from connector to bare wires
Weight	0.2 lbs (90 g)
Material	PVC insulated wires, plastic connector housing
Features	Retains factory features like chimes, door locks, and warning tones
Installation	Simple plug-and-play, minimal tools required
Maintenance	Wipe with dry cloth; avoid moisture
Safety	Disconnect vehicle battery before installation
Warranty	1-year limited warranty
Package Contents	1 x Wiring harness, 1 x instruction sheet

Frequently Asked Questions - 95-6506B Metra

What vehicles is the Metra 95-6506B compatible with?

The Metra 95-6506B is designed for select General Motors vehicles from 1998 to 2005, including popular models like Chevrolet Malibu, Pontiac Grand Am, and Oldsmobile Alero. Check your vehicle's specific radio connector to confirm compatibility.

Does this harness retain factory chimes and door lock functions?

Yes, the 95-6506B is engineered to retain factory features such as door chimes, turn signal sounds, and warning tones when used with compatible aftermarket radios.

How do I install the Metra 95-6506B wiring harness?

Installation is straightforward: disconnect the vehicle battery, remove the factory radio, unplug the factory connector, plug the 95-6506B harness into the vehicle side, then connect the bare wires to your aftermarket radio's harness using crimp connectors or solder. Finally, mount the new radio and test functions.

Do I need additional parts for installation?

For a complete installation, you may need a dash kit (e.g., Metra 99-3303) and an antenna adapter (e.g., Metra 40-GM10). The 95-6506B only handles the wiring connection.

What wire colors are used on the 95-6506B?

The harness follows aftermarket standard colors: yellow (battery 12V constant), red (accessory 12V switched), black (ground), orange/white (dimmer), blue/white (amp remote), and speaker wires (white/black for front left, gray/black for front right, green/black for rear left, purple/black for rear right).

Can I use this harness with a non-GM vehicle?

No, the 95-6506B is specifically designed for GM vehicles with a 24-pin connector (pre-2006). Using it with other brands may require cutting and splicing, which is not recommended.

Does the harness support steering wheel controls?

The standard 95-6506B does not include wiring for steering wheel controls. For SWC retention, you need an additional adapter like the Metra ASWC-1.

What is the length of the harness wires?

The bare wire tails are approximately 8 inches (20 cm) long, which is sufficient for most installations. If you need extra length, use quality wire extenders.

Is the harness plug-and-play?

Yes, the connector side is plug-and-play with the vehicle's factory radio plug. Only the wire-to-wire connections to the aftermarket radio require manual splicing or crimping.

What should I do if my vehicle's connector doesn't match?

Verify your vehicle's connector shape and pin count. The 95-6506B uses a 24-pin rectangular connector. If it doesn't match, you may need a different Metra harness or an adapter. Check online resources or contact Metra support.

USER MANUAL 95-6506B Metra

Interior view of an airplane cabin showing the air conditioner panel and control buttons (no visible text or symbols)

Chrysler Pacifica 2004-2008

KIT FEATURES

• ISO DDIN radio provision
• Painted matte black to match the factory appearance

KIT COMPONENTS

• A) Radio brackets

A

Technical line drawings of two mechanical bracket components (no text or symbols)

TABLE OF CONTENTS

Dash Disassembly 2

Kit Preparation ....3

Kit Assembly 3

WIRING & ANTENNA CONNECTIONS(sold separately)

Wiring Harness: CHTO-02 amplified interface

• 70-6506 amplified bypass harness

Antenna Adapter: 40-CR10

TOOLS REQUIRED

• Phillips screwdriver • Socket wrench
- Small flat blade screwdriver • Cutting tool

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

DASH DISASSEMBLY

1. Loosen (1) T-15 Torx screw from the front side of the shift knob and pull up to remove. (Figure A)
   Note: For models equipped without a release lever on the shift knob, just turn counter-clockwise to remove.
2. Unsnap the floor console trim around the shifter. Unplug the harness to console trim and remove the trim. (Figure B)
3. Unsnap and remove the ignition key trimring.

(Figure A) (Figure C)

1. Unsnap and remove the dash trim panels from each side of the radio/climate controls. (Figure C)
2. Remove (4) Phillips screws to remove the radio.

Continue to Kit Preparation

Top-down diagram of a car air intake console with control panel and fan (no text or labels)

(Figure B)

KIT PREPARATION KIT ASSEMB

1. Cut and remove the sub-dash to allow clearance for the aftermarket radio. (Figure A)

Continue to Kit Assembly

(Figure A) (Figure A)

ISO DDIN radio provision

1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A)
2. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation.
3. Secure the completed assembly into the dash using the factory screws.
4. Reassemble the dash in reverse order of disassembly.

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected

anrolling in the most recognized and resp mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

Metra recommends MECP certified technicians

Black metal bracket with cutouts and a slot, no visible text or symbols

Black metal bracket with mounting holes and a vertical slot (no text or symbols visible)

Chrysler Pacifica 2004-2008

ISO DDIN radio provision

Painted matte black

This kit provides the ability to install an ISO DDIN aftermarket radio. Painted matte black to match the original dash appearance.

KIT COMPONENTS

- Radio brackets

WIRING & ANTENNA CONNECTIONS

(sold separately)

- Wiring Harness: CHT0-02 amplified interface 70-6506 amplified bypass interface

- Antenna Adapter: 40-CR10

SALES 800-221-0932