SSB159 - Projector Accessories Chief - Free user manual and instructions

Product Type	Projector Mount
Compatibility	Most standard projectors up to 50 lbs (22.7 kg)
Mounting Pattern	Universal (up to 400x400 mm VESA)
Extension	Adjustable length 12-24 inches (305-610 mm)
Material	Steel and aluminum alloy
Color	Black
Dimensions (W x H x D)	6 x 6 x 20 inches (152 x 152 x 508 mm)
Weight	4.5 lbs (2.04 kg)
Load Capacity	50 lbs (22.7 kg)
Tilt Adjustment	±15°
Swivel Adjustment	±90°
Roll Adjustment	±3°
Mounting Type	Ceiling or wall mount
Projector Plate	Removable and adjustable
Installation	Includes hardware for concrete, wood, and steel studs
Cable Management	Built-in cable channels
Key Features	Easy tilt and swivel, quick release, safety latch
Warranty	5 years
Certifications	UL listed, TUV approved
Cleaning Instructions	Wipe with a dry cloth; do not use solvents
Spare Parts Availability	Contact Chief customer service
Repair Information	Refer to manual for troubleshooting; professional installation recommended
Environmental	Indoor use only, 32°F to 104°F (0°C to 40°C)

Frequently Asked Questions - SSB159 Chief

What is the maximum weight the Chief SSB159 can support?

The Chief SSB159 projector mount can support projectors up to 50 lbs (22.7 kg).

Is the SSB159 compatible with all projectors?

It is compatible with most projectors that have a VESA pattern up to 400x400 mm. Check your projector's mounting hole pattern.

Can the SSB159 be mounted on a wall?

Yes, the SSB159 can be mounted on walls or ceilings. It includes hardware for concrete, wood, and steel studs.

How do I adjust the tilt on the SSB159?

Loosen the tilt adjustment knob, set the desired angle (up to ±15°), and retighten the knob.

Does the SSB159 come with a template for drilling?

Yes, a mounting template is included in the box to help with accurate hole placement.

How do I secure the projector to the mount?

Attach the projector plate to the projector using the included screws, then slide the plate onto the mount until it locks. Use the safety latch for extra security.

Can I use the SSB159 for outdoor projectors?

No, the SSB159 is designed for indoor use only. Exposure to moisture or extreme temperatures may damage the mount.

Does the SSB159 have cable management?

Yes, it features built-in cable channels to route and hide cables neatly.

What tools are needed for installation?

You will need a drill, screwdriver, wrench, and level. All mounting hardware is provided.

How do I clean the Chief SSB159?

Wipe the mount with a dry cloth. Do not use harsh chemicals or solvents as they may damage the finish.

USER MANUAL SSB159 Chief

INSTALLATION INSTRUCTIONS

SSB-159, SSM-159, SLB-159 and SLM-159 Interface Brackets

SSB-159, SSM-159, SLB-159 and SLM-159 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

(1) Interface Bracket (4) Screw, Phillips Flat Head Cap, Machine, M4 x 25mm ****
(4) 10-24 Thumb Nuts ** (4) 1/2" x .257" x 5/8" Nylon Spacer ****
(1) All-Points Security Kit

SLB-159
(Note: SSB-style interface bracket connections are encircled)

SLM-159
(Note: SSM-style interface bracket connections are encircled)

**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket on the bottom of the projector so the mounting holes in the bracket align with the mounting inserts in the bottom of the projector.
4. Attach the interface bracket using the M4 x 25mm screws and M4 washers. Tighten all fasteners at this time, securing the bracket to the projector.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in the All-Points Security Kit.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

CHIEF®

Our Mounts. Your Vision.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000228 Rev01

©2009 Milestone AV Technologies,

a Duchossois Group Company

05/09