Gotham 60/191 - Lighting NUVO - Free user manual and instructions

Product Type	Floor Lamp
Model	Gotham 60/191
Brand	NUVO
Height	1910 mm
Base Diameter	600 mm
Weight	5.5 kg
Material	Metal with fabric shade
Power Supply	220-240 V, 50 Hz
Light Source	Integrated LED module (40W)
Color Temperature	3000K (warm white)
Luminous Flux	4000 lm
Dimmable	Yes, with compatible dimmer
Main Functions	Ambient lighting, adjustable brightness via dimmer
Assembly Required	Minimal assembly (attach shade to base)
Maintenance & Cleaning	Wipe with a dry cloth; avoid harsh chemicals
Safety	Use only with specified voltage; keep away from moisture; check cord regularly
Spare Parts & Repairability	LED module replaceable by a qualified technician; contact NUVO support
General Information	Suitable for indoor use; style: contemporary

Frequently Asked Questions - Gotham 60/191 NUVO

How do I assemble the Gotham 60/191 floor lamp?

Assembly is straightforward. Attach the fabric shade to the metal base by screwing it onto the threaded rod. Ensure all connections are tight but do not overtighten. Refer to the manual for detailed step-by-step instructions.

What type of bulb does it use?

The Gotham 60/191 uses an integrated LED module (40W). It is not designed for traditional bulb replacement, but the LED module can be replaced by a qualified technician if needed.

Is the lamp dimmable?

Yes, the lamp is dimmable when used with a compatible phase-cut dimmer. We recommend using a leading-edge or trailing-edge dimmer rated for LED loads.

What is the color temperature?

The color temperature is 3000K (warm white), which creates a cozy and relaxing ambiance suitable for living rooms and bedrooms.

Can I use this lamp outdoors?

No, the Gotham 60/191 is designed for indoor use only. Exposure to moisture or extreme temperatures may damage the electrical components and pose a safety hazard.

How do I clean the lamp?

Always unplug the lamp before cleaning. Wipe the metal parts with a soft, dry cloth. For the fabric shade, gently vacuum with a brush attachment or spot clean with a damp cloth. Do not use abrasive cleaners.

What voltage does the lamp require?

The lamp operates on a standard 220-240V, 50Hz power supply. Using it with a different voltage can cause malfunction or risk of fire.

How tall is the lamp?

The total height of the Gotham 60/191 is 1910 mm (about 6.3 feet). The base diameter is 600 mm.

Is it heavy?

The lamp weighs approximately 5.5 kg. It is stable enough for everyday use but should be placed on a flat, level surface to prevent tipping.

What should I do if the LED fails?

If the LED module stops working, contact NUVO customer support for assistance. The module can be replaced by a qualified electrician. Do not attempt to open the lamp yourself.

USER MANUAL Gotham 60/191 NUVO

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

STEP 2: Thread the nipple (K) into column (L) and the coupling (M).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Thread nut (D) onto nipple (E) so that five threads are exposed above nut (D). Insert lock washer (C) and thread nipple (E) onto mounting bar (A), then secure with the nut (D), secure mounting bar (A) to outlet box with outlet box screws (B).

STEP 2: Thread screw collar (H) onto the nipple (E). Slide screw collar ring (G) and canopy (F) over chain (I). Using two pairs of pliers, open one link of chain (I) and connect it to the fixture loop (J).

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.

STEP 3: Lace wires up through chain (I) and pass wires through holes in screw collar (H). We recommend lacing wire up through every other link of chain (I).

GROUNDING INSTRUCTIONS

STEP 1: The green grounding screw is to be inserted into the hole with two raised dimples provided on the mounting bar. Wrap the ground wire from the fixture (if supplied) and the ground wire from the outlet box (bare metal) or green insulated wire around the green grounding screw on the mounting bar. If uninstalled wire is on the mounting bar, connect the ground wire from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied).

NOTE: Underwriters Laboratories does not require all fixtures to have ground wires. These fixtures still meet all U. L. specifications.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

GROUP A: Connect to Black House Wire	GROUP B: Connect to White House Wire
BLACK	WHITE
*PARALLEL WIRE (round & smooth)	*PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER	WHITE OR GREY WITHOUT TRACER
BROWN GOLD OR BLACK WITHOUT TRACER	BROWN, GOLD OR BLACK WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.

STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside outlet box, then secure canopy (F) with screw collar ring (G).

STEP 2: Thread nut (P) onto the nipple (Q) then thread the nipple (Q) into the coupling (N) and secure the nipple (Q) with nut (P).

STEP 3: Raise the column (O) and cap (R) onto the nipple (Q) then secure with finial (S).

STEP 4: Slide the glass shade (U) over the socket (T) and secure with the retaining ring (V).

STEP 5: Install lamps. (Please do not exceed the maximum capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.