9007 - Lamp Currey & Company - Free user manual and instructions

Product Type	Table Lamp
Brand	Currey & Company
Model	9007
Height	28 inches
Base Diameter	10 inches
Shade Diameter	14 inches
Weight	5 lbs
Bulb Type	E26 Medium Base
Maximum Wattage	100W
Number of Bulbs	1
Switch Type	3-way Rotary Switch
Material	Metal Base, Fabric Shade
Cord Length	6 ft
Voltage	120V
Power Source	Plug-in
Recommended Bulb	LED or Incandescent
Assembly Required	Yes (shade and finial)
Care Instructions	Wipe with dry cloth
Safety Certification	UL Listed
Warranty	1 Year

Frequently Asked Questions - 9007 Currey & Company

Does the lamp come with a light bulb?

No, the lamp does not include a bulb. You will need to purchase an E26 medium base bulb separately, up to 100W.

What is the assembly process like?

Assembly is simple: attach the lamp shade to the harp, then screw on the finial. No tools are required.

Can I use an LED bulb?

Yes, you can use an LED bulb with an E26 base, as long as it does not exceed 100W equivalent.

Is the lamp dimmable?

The lamp uses a 3-way rotary switch, which allows for low, medium, and high settings when used with a 3-way bulb. For dimming, use a compatible dimmer bulb.

How do I clean the lamp?

Wipe the metal base with a dry or slightly damp cloth. For the fabric shade, use a soft brush attachment on a vacuum or gently dab with a dry cloth.

What is the warranty period?

Currey & Company offers a 1-year warranty against manufacturing defects. Keep your receipt.

Can I use the lamp outdoors?

No, this lamp is for indoor use only. Do not expose it to moisture.

What if the switch stops working?

The switch can be replaced by a qualified electrician. Alternatively, contact Currey & Company customer service for assistance.

Are replacement parts available?

Yes, replacement parts such as shades and finials may be available through authorized dealers or the manufacturer.

How long is the power cord?

The power cord is 6 feet long.

USER MANUAL 9007 Currey & Company

Chandelier Installation Instructions

These instructions are provide for your safety. It is very important that they are read carefully and completely before beginning installation of this chandelier. We strongly suggest that all direct wired fixtures be installed by a professional electrician.

BEFORE ASSEMBLY

Your chandelier should have the following hardware included in the installation kit:

1. Canopy plate
2. Mounting strip with green ground screw
3. Threaded pipe nipple
4. Nipple assembly with locknut
5. Chain, electrical supply and ground wire

TO ASSEMBLE

1. Shut off the main electrical supply from the fuse box/circuit breaker.
2. Remove existing fixture – loosen the locknut while holding the canopy plate with one hand. Lower the canopy plate. This exposes the outlet box that holds the wiring.
3. Unscrew the plastic wire nuts and disconnect the black and white house wires from the old fixture. Disconnect the ground wire (save the wire nuts). Remove the nipple and mounting strip that crosses the outlet box and replace with new ones from installation kit.
4. Determine the distance to suspend your chandelier from the ceiling and if necessary, remove the extra links from the chain and reconnect the chain to the nipple (hook) assembly. The electric supply wire that is woven through the chain should be cut off 12 inches longer than the chain. Cut the braided copper ground wire the same length. Split the supply wire down the center by a length of 3 inches and

strip 34 inch of insulation off the end of each wire. If you look very closely, you will notice that the plastic insulation of one of the two split wires has a rib on the outside edge. This ribbed wire is the “neutral” wire and the other is the “hot” wire; you will need to remember the difference later on when you connect these to the house wires in the electrical outlet box.

1. Insert the two stripped wires and the braided copper ground wire through the nipple assembly, locknut, mounting plate and mounting strip. Using the wire nuts that you saved, attach the ribbed wire to the white "neutral" house wire and the un-ribbed wire to the black "hot" house wire. Secure the wire nuts with black electrical tape. Connect the braided copper ground wire to the green ground screw marked "GRD" on the mounting strip. It is imperative that the outlet box in your home be properly grounded.
2. Please note: Do not reverse the hot and neutral connections. Always make sure that no wire strands are outside of the wire nut connectors.
3. Gently push the wiring back into the outlet box. Screw the nipple assembly, locknut and canopy plate into the mounting strip and turn until the canopy is snug against the ceiling. Please do not support fixture from the electrical cord.
4. Restore power to the electrical outlet box.

Care for your chandelier:

Dust with a soft dry cloth. To protect the finish, do not use cleaners or abrasives.