SSB343 - Projector Accessories Chief - Free user manual and instructions

Product Type	Interface Bracket for Projector Mounts
Brand	Chief
Model	SSB343
Compatible Mounts	Chief Series Projector Mounts (SSM, SLB, SLM interfaces)
Included Hardware	1 interface bracket, 4 M4x12mm Phillips pan head screws, 6 10-24 thumb nuts, 4 M4x12mm button head security screws, 4 M4 flat washers, 1 All-Points Security Kit, 1 5/32 hex key
Screw Type	M4 machine screws (Phillips and button head)
Installation Orientation	Triangle on bracket points toward front of projector
Safety Warning	Improper installation can cause equipment falling; use only supplied hardware
Torque Warning	Do not over tighten screws to avoid damage
Security Feature	All-Points Security Kit allows substitution of standard screws
Special Installation Note	SLB/SSB brackets require thumb nuts; SLM/SSM brackets do not
Material	Metal (steel or aluminum)
Color	Black or silver (not specified)
Dimensions	Approximately 6 x 4 x 1 inches (estimate)
Weight	Approximately 0.5 lbs (estimate)
Manufacturer	Milestone AV Technologies, Eden Prairie, MN, USA
Document Number	8800-002801 Rev00
Date	2015

Frequently Asked Questions - SSB343 Chief

What is the SSB343 Interface Bracket used for?

The SSB343 is an interface bracket designed to attach a projector to Chief Series Projector Mounts. It provides a secure mounting point between the projector and the mount.

Which mounts are compatible with the SSB343?

The SSB343 is compatible with Chief Series Projector Mounts, specifically those designed for SSB, SSM, SLB, and SLM interface brackets. Refer to the mount's installation instructions for specific compatibility.

What hardware is included with the SSB343?

The kit includes 1 interface bracket, 4 M4x12mm Phillips pan head screws, 6 10-24 thumb nuts, 4 M4x12mm button head security screws, 4 M4 flat washers, 1 All-Points Security Kit, and 1 5/32 inch hex key.

How do I install the SSB343 on a projector?

Turn the projector upside down on a flat surface. Place the bracket on the bottom of the projector, aligning the mounting holes and ensuring the triangle points toward the front. Secure with M4 screws and washers into the threaded inserts and bracket side tabs. Tighten all fasteners.

What is the purpose of the triangle marking on the bracket?

The triangle indicates the front of the projector. When installing, point the triangle toward the front of the projector to ensure correct orientation.

Can I use security screws instead of the standard screws?

Yes, the included All-Points Security Kit allows you to substitute the standard Phillips screws with the button head security screws for added theft deterrence. Follow the instructions in the security kit.

What should I avoid during installation?

Avoid over tightening the screws, as this can damage parts and lead to equipment failure. Also, do not substitute hardware; use only the supplied screws and washers.

What is the difference between SSB, SSM, SLB, and SLM brackets?

The SSB and SSM are different interface styles. SSB-style brackets use thumb nuts (included) and have specific screw locations; SLB and SLM are similar but with different mounting patterns. The SSB343 is specifically for SSB-style but instructions cover all four.

Where can I find additional installation information?

Refer to the specific installation instructions provided with the Chief Series Projector Mount. The SSB343 manual includes general steps but the mount's manual has detailed guidance.

Who manufactures the SSB343?

The SSB343 is manufactured by Milestone AV Technologies, located at 6436 City West Parkway, Eden Prairie, MN 55344. Chief is a registered trademark of Milestone AV Technologies.

USER MANUAL SSB343 Chief

INSTALLATION INSTRUCTIONS

SSB-343, SSM-343, SLB-343 and SLM-343 Interface Brackets

SSB-343, SSM-343, SLB-343 and SLM-343 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M4 x 12mm
(6) 10-24 Thumb Nuts ** (4) Screw, Button Head, Security, M4 x 12mm
(1) All-Points Security Kit (4) Washer, Flat, M4
(1) 5/32" Hex Key

SLB-343
Note: SSB-style interface bracket connections are circled.

SLM-343
Note: SSM-style interface bracket connections are circled.

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the bottom of the projector and ensuring that triangle in bracket points towards front of projector.
4. Position M4 x 12mm mounting screws with M4 flat washers into the threaded inserts and bracket side tabs. Tighten all fasteners at this time, securing the bracket to the projector.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the All-Points Security Kit.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

CHIEF®

Our Mounts. Your Vision.

Chief, a products division of Milestone AV Technologies

6436 City West Parkway, Eden Prairie, MN 55344

• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918

8800-002801 Rev00

©2015 Milestone AV Technologies

11/15