Icarus 400 - Tent Vango - Free user manual and instructions

Product Type	4-person family tent
Brand	Vango
Model	Icarus 400
Sleeping Capacity	4 persons
Floor Dimensions	400 x 200 cm (length x width)
Floor Area	Approximately 8.0 m²
Peak Height	185 cm
Packed Weight	14.5 kg
Pole Type	Fiberglass poles with color-coded sleeves
Flysheet Fabric	Polyester, 190T, waterproof coating
Flysheet Hydrostatic Head	3000 mm
Inner Tent Fabric	Breathable polyester with mesh panels
Groundsheet Fabric	Polyethylene, sewn-in bathtub style
Ventilation	Adjustable vents with mesh insect screens
Number of Doors	2 (front and rear)
Storage Pockets	Multiple internal mesh pockets
Peg Type	Steel ground pegs (included)
Guy Ropes	Reflective guy ropes with tensioners
Carry Bag	Durable compression sack with handles
Recommended Use	Family camping, festival use

Frequently Asked Questions - Icarus 400 Vango

How do I set up the Vango Icarus 400 tent?

First, lay out the tent and peg down the corners. Assemble the fiberglass poles by color-coding and insert them into the corresponding sleeves. Lift the tent and secure poles into the grommets. Finally, attach the flysheet and adjust guy ropes for stability.

What is the hydrostatic head rating of the flysheet?

The flysheet has a hydrostatic head of 3000 mm, providing good protection against moderate to heavy rain.

Can the tent be used in windy conditions?

Yes, the Icarus 400 is designed with reflective guy ropes and steel pegs to withstand moderate winds. Ensure all guylines are taut and pegs angled away from the tent for best stability.

How many people can sleep comfortably inside?

The tent is designed for 4 persons in a single large sleeping area. For added comfort, we recommend using it for 3-4 people with gear in the vestibules.

Is the groundsheet waterproof?

Yes, the sewn-in bathtub groundsheet is made from polyethylene and is fully waterproof. Keep the groundsheet clean and avoid sharp objects to maintain its integrity.

How do I clean and maintain the tent?

After each trip, brush off dirt and rinse with fresh water. Use a mild soap if needed, never detergents. Allow the tent to dry completely before storage. Store in a cool, dry place away from direct sunlight.

Can I replace damaged poles?

Yes, replacement poles are available from Vango or camping retailers. The fiberglass poles can be replaced individually. Contact Vango customer service for exact part numbers.

Does the tent have a porch or vestibule area?

The Icarus 400 features two doors with mesh panels and small covered vestibules for storing boots and gear outside the sleeping area.

How long does it take to set up?

With two people, setup typically takes 15-20 minutes after initial practice. Color-coded poles and sleeves make assembly straightforward.

What is the warranty on this tent?

Vango offers a 2-year warranty against manufacturing defects. Keep your purchase receipt and register the product online to activate warranty.

USER MANUAL Icarus 400 Vango

Black-and-white photo of a Vango camping tent and its logo, no text or symbols on the tent itself.

Tent Pitching Instructions – Icarus 400

FLYSHEET FIRST PITCHING

• Assemble the poles and lay them parallel on the ground.
• Open out flysheet and position in required direction.
• Insert the poles through the pole sleeves on the outside of the flysheet, matching the colour of the middle pole section to the coloured tab at the pole sleeve end.
• Locate one end of each pole on one side of flysheet into the Ring & Pin system at the base of the tent. Make sure poles locate into correct pin system (all poles follow corresponding flysheet seams to pin system).
• Push poles into an arch from opposite ends and locate pole ends into corresponding metal pin.
• Tighten the tension adjusters located on the Ring & Pin webbing.
  • Start pegging out the main corners at the rear of the tent using the pin pegs provided.
  • Pull the tent forward until taut and peg out the main corners at the front of the tent, again with the pin pegs.
• Ensure the tent is in a straight line.
• Secure the tent using the pin pegs through the Ring & Pin system (see fig 2).
  • Peg out ALL guy lines, ensuring that they are in line with the pole or seam they are attached to.

INNER ATTACHMENT

• Suspend the inner by attaching toggles on the inner tent through rings on the inside of the flysheet. Do the rear first and work towards the front of the tent.
• Once fully attached, the inner can be left in when pitching or striking the tent. However, it is advisable to remove the inner when striking the tent when wet.

TENSION BAND SYSTEM

• Remove Tension Band System from pockets and attach into the corresponding clips at the apex of the pole. Adjust the straps until they are taut.
  • DO NOT OVER TENSION. Excess tension will alter the shape of the tent.
• Tension bands are designed to stabilise the tunnel structure of the tent. The bands are not required to be used in calm weather.

Close-up of a mechanical tool interacting with a curved surface (no text or symbols visible)

Figure 1.

Diagram of a rope tied to a hook with grass at the base (no text or symbols)

Figure 2.

Ring & Pin System

1. Locate one end of each pole onto the corresponding metal pin. The metal pin inserts into the hollow metal ferrule on the end of each pole. (See Figure 1). Push the pole into a curve from the opposite side, one at a time, and locate all pole ends onto the metal pins.
2. Peg the corners of the tent through the metal rings using pin-pegs. It is important to drive the peg into the ground at a 45 degree angle to obtain the best grip. (See Figure 2).