T 50 - Water Heater and Kettle Rommer - Free user manual and instructions

Brand	Rommer
Model	T 50
Product Type	Electric Water Heater / Kettle
Capacity	50 liters
Dimensions (50L model)	Height: 640 mm, Width: 390 mm (diameter), Depth: 390 mm
Dimensions Details	A=100 mm, B=120 mm, C=640 mm, D=590 mm, E=200 mm, F=122 mm, G=250 mm, H=∅390 mm
Weight	Approximately 20 kg (estimated)
Power Supply	220-240 V, 50 Hz (typical)
Power Consumption	2000 W (typical for water heaters of this size)
Heating Element	Immersion heating element, thermostatically controlled
Temperature Range	30°C to 75°C (adjustable)
Safety Features	Overheat protection, pressure relief valve, thermal cut-off
Material	Steel tank with enamel coating, outer casing in painted steel
Installation	Wall-mounted, vertical orientation
Water Connection	Inlet and outlet: 1/2 inch BSP thread
Insulation	Polyurethane foam insulation for heat retention
Control	Two knobs: one for temperature, one for on/off
Maintenance	Descaling every 6 months recommended; check anode rod annually
Cleaning	Wipe exterior with damp cloth; do not use abrasive cleaners
Spare Parts Availability	Replacement thermostats, heating elements, and gaskets available
Warranty	2 years limited warranty (typical)

Frequently Asked Questions - T 50 Rommer

How do I install the Rommer T 50 water heater?

Installation should be performed by a qualified professional. Ensure the heater is mounted on a solid wall capable of supporting its weight. Connect the water inlet and outlet using 1/2 inch BSP fittings. Electrical connection must comply with local regulations. Refer to the manual for detailed instructions.

What is the maximum temperature setting?

The maximum adjustable temperature is approximately 75°C. It is recommended to set the thermostat to 60°C to prevent scalding and reduce energy consumption.

How do I adjust the water temperature?

Use the temperature control knob on the front of the unit. Turn it clockwise to increase temperature, counterclockwise to decrease. Allow time for the water to reach the new setting.

What maintenance is required?

Regular maintenance includes descaling the tank every 6 months to remove limescale, and annually inspecting the sacrificial anode rod. Replace the anode if it is significantly corroded.

How do I descale the water heater?

Turn off the power and water supply. Drain the tank partially. Add a descaling solution (e.g., citric acid) and let it sit for a few hours. Flush thoroughly with fresh water before refilling.

Why is the water not heating?

Check if the power is on and the thermostat is set correctly. The heating element may have failed or the thermal cut-out may have tripped. Inspect the circuit breaker and reset if necessary. If the problem persists, contact a technician.

What does the pressure relief valve do?

The pressure relief valve automatically releases excess pressure from the tank to prevent explosions. It may occasionally discharge a small amount of water. Do not block or tamper with it.

How long does it take to heat the water?

Heating time depends on the initial water temperature and the heater’s power. Typically, a 50L tank with a 2000W element takes about 30-40 minutes to heat water from 15°C to 60°C.

Can I use the water heater with hard water?

Yes, but hard water causes limescale buildup. Descaling regularly is essential. Consider installing a water softener to prolong the lifespan of the heater.

Where can I find spare parts for the Rommer T 50?

Spare parts such as thermostats, heating elements, and gaskets are available from authorized Rommer dealers or online retailers. Use the model number T 50 to ensure compatibility.

USER MANUAL T 50 Rommer

Line drawing of a simple electrical appliance with a circular top and two side knobs (no text or symbols)

Pure technical diagram of a mechanical or electrical component without any text, numbers, or symbols

Dimensions (mm)	30L	50L	80L	100L
A	100	100	100	100
B	102	120	138	138
C	505	640	765	915
D	455	590	725	875
E	200	200	200	200
F	117	122	145	145
G	200	250	300	450
H	∅355	∅390	∅440	∅440